Kyocera Mita KM-C830 Operation Manual Download Page 143

Page: 143 / 161

Section 9 TROUBLESHOOTING

9-10

Open the front cover.

Operate the paper conveyor release lever and pull the paper
conveyor out towards you as far as it will go.

Grasp the green handle (shown as

in the illustration) to

the left cover to the fixing unit and open that cover.

Replace the paper conveyor in its original position in the
copier.

Close the front cover.
* Be sure to hold both the left and right sides of the front

cover and close it securely.

Misfeed in the fixing section

If “Paper misfeed. Remove paper from Fixing unit.” is displayed and
the misfeed location indicator shown in the illustration lights, a
misfeed has occurred in the fixing section. Perform the following
procedure to remove the jammed paper.

WARNING

High voltage is present in the charger section. Take
sufficient care when working in this area, as there is
a danger of electrical shock.

CAUTION

The copier’s fixing unit is extremely hot. Take
sufficient care when working in this area, as there is
a danger of getting burned.

Summary of Contents for KM-C830


































































































































































Search results

Summary of Contents for KM-C830

Reviews:

Related manuals for KM-C830

Brands by name

Popular brands

Kyocera Mita KM-C830, Operation Manual

Search results

Summary of Contents for KM-C830

Reviews:

Related manuals for KM-C830

Brands by name

Popular brands