KYMCO X-Town 300 Manual Download

Page: 22 / 69

CONTROLS & FEATURES

The battery voltage

Display the prompt battery voltage to get the
information without need to check battery directly.

The ambient temperature mode

Display the surrounding temperature, Press the
“FUNC” and “RESET” buttons for 3 seconds to
select the unit of

“

“ Celsius or “

” Fahrenheit.

The oil service trip meter

Display the accumulated driving distance from the
previous reset after the oil service.
Press the

“RESET” button for 3 seconds to reset the

oil service indicator and the oil service trip meter.

The Fi error code indicator

Display the error code of fuel injection
system. If appear any error codes and
display continuously, have the KYMCO
authorized dealer check the vehicle.

▆

NOTE:

If any error codes show up for a moment

then goes off and not repeat, it could result from an
electrical interference.

WARNING

If any error codes always show up, the
vehicle should be checked immediately.

TRIP A

TRIP B

OIL

SERVICE

VOLT

AIR

1 3

X-Town300

Summary of Contents for X-Town 300






































































Search results

Summary of Contents for X-Town 300

Reviews:

Related manuals for X-Town 300

Brands by name

Popular brands

KYMCO X-Town 300, Manual

Search results

Summary of Contents for X-Town 300

Reviews:

Related manuals for X-Town 300

Brands by name

Popular brands