KXDMOTO.de
The position of the VIN
The VIN is on the right side of the front frame.
Key switch
Key switch is on the right side of the vehicle front part, indicating "OFF" and "NO".
"OFF" condition: Key can be taken out. Light can not be turned on (if light available); engine can not be
started.
"ON” condition: Key can not be taken out. When engine is being started, headlight can be turned on (if
headlight available).
Function Switch
Functional switch is in left side of handlebar, which consists of horn, start, headlight, flame-out function.
1. Electric horn button ‘
’, When key switch is on, press it, then it rings.
(2 stroke, pull start engine have not equipped electric horn as the product construction. But manual horn
should be assembled according to customers’ needs.)
2. Start horn button: Red, ‘
’Press it to start the vehicle (when brake hand is ready ).
3. H
eadlight button:
‘
’near light;‘
’distance light .
4. Turn-off switch:‘
’ turn off;‘
’turn on.
Charger (optional)
1. The input voltage is 220V or 110V (the same as voltage in local place), and output voltage is12V.
2. When the vehicle is charging, the indicator light turns to be red. When the vehicle is fully charged, the
indicator light turns to be green.
Burglar alarm (optional)
1. The input voltage is 12V.
Anti-theft function: Press the “lock” key, vehicle is in alerting condition.
2. Keyless function: Don’t need to turn on the key switch. Press the “start” button twice continuously, and
then operate the vehicle.
3. Telecontrol stop function: With the keyless function used first, press the button of “unlock” within the
certain distance of remote control, the power of vehicle will be turn off)
(Please note: This function is ineffective if vehicle is to be turned by key switch).
Emergency turn off stop switch
It’s put in the left side of the rear frame, or on the left handlebar. Pull or press down the switch, the engine
will be stopped.
The emergency rope can be fastened on the driver when there is emergency, the vehicle will be stopped
automatically by the driver getting off the seats and pulling down the rope.
Tire and Tire gauge
VIN number
KXDMOTO.de
KXDMOTO.de
Tire: The proper tire pressure can provide the maximum stability and comfortableness.
Do check and adjust the tire pressure regularly, to make sure the pressure to be on the standard grade.
To find the tire size and standard pressure, please check parameter list and warning label on
the vehicle. To find the “Load-bearing” and “speed grade”, please check the tire surface.
1. Check tire pressure and condition before driving. Please make the replacement if there is any
following condition happened: broken, stabbing
,
or rim is out of shape.
(Please seek assistance from
qualified technician or local retailer for replacement.)
2. Improper tire pressure will result in hazards. Over the standard pressure can cause a flat tire.
Lower than the standard pressure can cause tire relaxation or even dropping, and resulting in losing control
of the vehicle.
3. When the tire-tread wearing is over 2mm,please replace new tire in time.
(Please seek assistance
from qualified technician or local retailer for replacement.)
Tire gauge (optional): Manufacturer will provide to customers to measure tie pressure.
Tire gauge is put on the key ring of the key switch for users' convenience.
Measure method
Unscrew valve cap
then press it toward the valve cap with tire gauge. The measured
value is tie pressure. Put back the valve cap and screw it after measuring. .
Operating
Inspection before riding
Idling inspection
1. Stabilize the vehicle
shake it up and down to inspect the swing arm and fork condition, to make
sure it move normally and without interference.
2. Check whether the front and rear the shock absorber is deformed or leakage or not.
3. Check whether the front suspension and the rear flat fork is fastened in place.
4. Hold the vehicle when checking.
5. Repair and replace parts in time when finding that negative phenomena.
6. Contact with the dealer when the situation is out of control.
Front brake inspection
Check whether the front brake installation is firm, the braking effect is valid.
1. Front brake handle is mounted on the right side.
2. The brake is working well if backward movement of the brake handle is in the top 20-30mm.
3. Check if the tire rotation is good after releasing the brake lever
4. Contact the dealer for the need of brake maintenance.
5. The front brake lever is with parking feature as well. Use it when parking.
Rear brake inspection
Check whether the rear brake installation is firm, the braking effect is valid.
1. The rear brake is mounted on the left hand, or on the right foot.
2. The brake is working well if backward movement of the brake handle is in the top 20-30mm or
downward movement of the top of the foot brake lever 20-30mm.
3. Put the brake lever or foot brake lever back into place quickly and check if the tire rotation is good
when the force is removed.
4. Contact the dealer for the need of brake maintenance.
5. Inspect the brake shoe regularly, and replace if timely when it is worn out as the brake shoe is a worn
pieces of block.
6. Do not open the brake casually as the brake fluid will damage people’s skin. Clean the skin with
KXDMOTO.de
