KVH Industries TracVision TV6 User Manual Download

Page: 85 / 104

TracVision TV5 User’s Guide

Troubleshooting

206

The antenna’s azimuth motor or limit switch failed.
Contact KVH.

207

The antenna’s elevation motor has a power failure.
Contact KVH.

208

The antenna’s elevation motor or limit switch failed.
Contact KVH.

217

The antenna’s skew motor has a power failure. Contact
KVH.

218

The antenna’s skew motor or limit switch failed. Contact
KVH.

221

The system is not receiving any data from the GPS.
Contact KVH.

222

The antenna’s internal temperature exceeds acceptable
limits. Turn off the system and allow it to cool.

223

The antenna’s main board has lost gyro calibration data. A
technician should calibrate the antenna’s gyros.

226

The antenna has lost RF communications. Contact KVH.

227

The antenna’s RF software might be corrupted. Contact
KVH.

228

The antenna has lost RF communications. Contact KVH.

229

The antenna’s RF software might be corrupted. Contact
KVH.

231

The antenna’s RF software might be corrupted. Contact
KVH.

232

The antenna’s RF software might be corrupted. Contact
KVH.

241

The antenna’s main board detects a power failure. Contact
KVH.

265

The GPS is unable to acquire a fix. Check for blockage or
RF interference around the antenna.

269

The main antenna processor detects that LNB voltage is
out of range. Contact KVH.

270

The azimuth or elevation gyro needs to be replaced.
Contact KVH.

Error

Description

Summary of Contents for TracVision TV6









































































































Search results

Summary of Contents for TracVision TV6

Reviews:

Related manuals for TracVision TV6

Brands by name

Popular brands

KVH Industries TracVision TV6, User Manual

Search results

Summary of Contents for TracVision TV6

Reviews:

Related manuals for TracVision TV6

Brands by name

Popular brands