KVH Industries TracPhone V3HTS Installation Manual Download

Page: 14 / 52

Follow these steps to connect the antenna cables.

Connect the power/data cable to the

“Power/Data” jack on the bottom of the

antenna (see Figure 18). Hand-tighten until

the connector locks in place.

Using the supplied 3 mm Allen hex key,

remove the connector cover from the

antenna’s baseplate. Save the cover and the

four M4 cap screws for later use.

Clean and dry the antenna’s RF connectors.

Place one of the supplied rubber washers

over the “MRx” jack on the bottom of the

antenna, as shown in Figure 19.

Fill half of the inner body of the “RX” pigtail

cable’s connector with silicone grease.

Connect and

SLOWLY

hand-tighten the

“RX” pigtail cable to the “MRx” jack on the

antenna, allowing the grease to diffuse and

settle into the entire space within the

connector.

Make sure the “RX” pigtail cable’s connector

is tightened all the way into the antenna’s

connector. Then tighten it with a 7/16" torque

wrench set to 20 in.-lbs. Make sure the rubber

washer compresses against the baseplate.

Repeat steps d-g to connect the “TX” pigtail

cable to the antenna’s “MTx” jack.

Wipe off any excess grease from the cables.

Seal all above deck RF cable connections with

silicone sealant or equivalent.

Reattach the connector cover and secure in

place with the M4 cap screws.

Secure the cables near the antenna connectors

to relieve stress.

Seal the cable access hole, as required.

RF C

les

Power/D

Cover

M4 C

Screw (x4)

MTX

MRX

Figure 18: Antenna Cable Connections

Antenn

sepl

ubb

er W

sher

Apply Silicone Gre

RG-11

Figure 19: Connecting RF Cables to the Antenna

The integrity and reliability of the RF cables is

critically important. Make certain that these

cables are properly terminated, sealed against

seawater and corrosion, strain-relieved,

protected from abrasion, and free of stress.

IMPORTANT!

Wire the Antenna

Summary of Contents for TracPhone V3HTS





















































Search results

Summary of Contents for TracPhone V3HTS

Reviews:

Related manuals for TracPhone V3HTS

Brands by name

Popular brands

KVH Industries TracPhone V3HTS, Installation Manual

Search results

Summary of Contents for TracPhone V3HTS

Reviews:

Related manuals for TracPhone V3HTS

Brands by name

Popular brands