KVH Industries TracPhone FB150 User Manual Download

Page: 45 / 140

Chapter 4: Using the web interface

Introduction

Accessing and navigating the web interface

Accessing the web interface

To access the web interface, do as follows:

1. Connect your computer to the terminal.

2. Start up the terminal.

For details, see

Getting started

on page 10.

3. Open your browser and enter

http://ut.bgan

or the IP address of the terminal in

the address bar.
If your connected computer is set up to obtain a DNS server address

automatically, this name is translated into the local IP address of the terminal.

The default IP address of the terminal is

http://192.168.0.1

Changing the language

When you have access to the web interface, if you want to display a different

language than English, select

SETTINGS > LANGUAGE

from the left menu, select

a language from the list and click

Apply

. For further information, see

Selecting the

language

on page 90.

Note

If the IP address is changed and you do not have the new address, you can

temporarily set the IP address to the default value by pressing the

Reset

button next to the SIM slot in the connector panel of the terminal. You can

then access the web interface and change the IP address.
Note that if you do not change the IP address, the default IP address will

only be valid until the terminal is powered off. Then the terminal returns to

the IP address from before the Reset button was pressed.
For further information on the Reset button, see

Reset button

on page 120.

Summary of Contents for TracPhone FB150













































































































































Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands

KVH Industries TracPhone FB150, User Manual

Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands