KVH Industries TracPhone FB150 User Manual Download

Page: 19 / 140

In this chapter

Chapter 2

Getting started

In this chapter

This chapter describes how to start up the system and make the first call or data

session.
For information on how to install the system, insert SIM card and connect cables,

refer to the installation manual for the TracPhone FB150 system.

Before you start

Operation at high temperatures

If the terminal is installed in a location where the ambient temperature may exceed



C, we recommend placing the terminal where unintentional contact is avoided.

Note that the maximum allowed ambient temperature is 55° C.
If the maximum ambient temperature does not exceed 50



C, the terminal can be

placed in a public area.
For further information on installation, refer to the installation manual for the

TracPhone FB150 system.

Connector panel

The drawing below shows the connector panel of the TracPhone FB150 terminal.

CAUTION!

In very high ambient temperatures, do not touch

areas of the terminal that are marked with this symbol.

tton

IM C

lot

Inp

Power

witch

Antenn

Phone

2 x LAN w/PoE

I/O

Gro

Summary of Contents for TracPhone FB150













































































































































Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands

KVH Industries TracPhone FB150, User Manual

Search results

Summary of Contents for TracPhone FB150

Reviews:

Related manuals for TracPhone FB150

Brands by name

Popular brands