KVH Industries Ka Tri-Americas LNB Installation Manual Download Page 17

Page: 17 / 19

Follow the instructions below to replace the SD

card inside the ACU.

NOTE:

This procedure requires handling exposed

electronic parts and components. Ensure that you take
the necessary grounding precautions before handling.

Using a #1 Phillips screwdriver, remove the

eight Phillips screws securing the ACU cover

(see

Figure 32

). Then remove the cover and

set it aside in a safe place.

Locate the SD card (see

Figure 33

Gently press and slide the locking tab to

unlock it (see

Figure 34

CAUTION

For your own safety, be sure to disconnect
power from all wired components before
performing this procedure.

Figure 32 ACU Cover Screws

Figure 33 SD Card Location

Figure 34 Locking Tab/SD Card

Screw (x8)

SD Card

Location

Locking

Tab

Lock

Unlock

SD Card

Replace the ACU SD Card

Summary of Contents for Ka Tri-Americas LNB




















Search results

Summary of Contents for Ka Tri-Americas LNB

Reviews:

Related manuals for Ka Tri-Americas LNB

Brands by name

Popular brands

KVH Industries Ka Tri-Americas LNB, Installation Manual

Search results

Summary of Contents for Ka Tri-Americas LNB

Reviews:

Related manuals for Ka Tri-Americas LNB

Brands by name

Popular brands