background image

O

ver

view

ESR3000

ESR3000

G

etting star

ted

Overview

Getting started

4

3

ESR3000 - 115V

 part num.  

KVV 987 275

ESR3000 - 230V

 part num.  

KVV 987 276

ESR3000 - 250V

 part num.  

KVV 987 277

Applications

Introductions

The ESR3000 Amplifier is three-way, active control and amplification system specially designed for the 

KV2 Audio ESR215 full range series loudspeaker systems. It houses all signal processing and amplification 

as well as providing control for external subwoofer cabinet configurations if needed, utilizing an external 

amplifier. The unit incorporates six amplifiers represented by two 100-watt, Class AB, push pull, low 

intermodulation amplifier for high frequencies, two 200-watt, Class AB, push pull, low intermodulation 

design for mids and two 1000 watt, high-efficiency, current-enhancing switch mode technology amplifier 

for bass. The ESR3000 stereo configuration powers two ESR cabinets accordingly.

 

Designed to drive and control the ESR215

 

Fixed Installations

Unpacking

Amplifier rack mounting

ESR3000 Amplifier Rack mounted

Unpack the ESR3000 Amplifier and check for 

any damage. If you find any damage, notify your 

supplier immediately. Only the consignee may 

institute a claim with the carrier for damage 

incurred during shipping. Be sure to save the 

carton and all packing materials for the carrier‘s 

inspection. Should you ever need to ship the 

unit, only use the original factory packaging. If 

the shipping carton is unavailable, contact your 

supplier to obtain a replacement.

The ESR3000 Amplifier carton should contain:

  ESR3000 Amplifier control unit

  This user guide

  Two PowerCon detachable power cables

The ESR3000 Amplifier is 4 rack units in height 

and will mount in standard 19“ rack systems. 

Integral rear mounting rack ears are also provided 

for additional support, do not rely on fixing and 

mounting the amplifier using just the front panel 

as support. Use eight screws and washers to 

mount the amplifier to the equipment rack rails. 

We recommend using a shock mounted rack for 

touring use to prolong the life of your amplifier.

Features

  The ESR3000 Amplifier is a stereo, three-way, active control and amplification system specifically 

designed for the KV2 Audio ESR Series - 

ESR215 The Ultimate Full Range System

  Houses all signal processing and amplification as well as providing control for external subwoofer 

cabinet configurations.

  External subwoofer is powered by the external subwoofer amplifier (VHD3200).

  The amplifier compliment inside the ESR3000 Amplier is as follows:

 - High Frequency - 100-watt, Class AB, push pull, low intermodulation design

 - Mid Frequency - 200-watt, Class AB, push pull, low intermodulation design 

 - Low Frequency - 1000-watt, high-efficiency, current-enhancing switch mode technology with 

Linear Active Filter

Summary of Contents for ESR215
























Reviews: