Kutai electronics ADVR-083, Operation Manual

Page: 2 / 6

___________________________________________________________________________________________
2
ADVR-083
SECTION 1 : SPECIFICATION
Sensing Input (E1, E2, E3) Average Reading Soft Start Ramp Time
Voltage and Frequency DIP switch settings 4 s/- 10%
1 phase (E1, E2) / 3 phase (E1, E2, E3)
90

130 Vac @ 110 Vac Voltage Regulation
180

260 Vac @ 220 Vac Less than +/- 0.5% (with 4% engine governing)
340

520 Vac @ 440 Vac
Frequency 50/60 Hz Typical System Response
Less than 20 milliseconds
Power Input (X1, X2, Z2)
Voltage 60

300 Vac, 1 phase / 3 phase EMI
1 phase ( X1, X2 ) / 3 phase ( X1, X2, Z2 ) Built-in Harmonic suppression
Frequency 40

500 Hz
Static Power Dissipation
Auxiliary Input (Z1, Z2) Max. 6 watts
Voltage 60

300 Vac, 1 phase 2 wire
Frequency 40

500 Hz
Under Frequency Protection (Factory Preset)
50 Hz system preset knee point at 45 Hz
Excitation Output (F+, F-) 60 Hz system preset knee point at 55 Hz
110V 1 phase Continuous 63 Vdc 8A
Max. 90 Vdc 10A for 10 secs. Over Excitation Protection
220V 1 phase Continuous 125 Vdc 8A 25

105% of Input Power (adjust with EXC pot.)
Max. 180 Vdc 10A for 10 secs. O/E acts after 10 sec. delay. The OE function can be
220V 3 phase Continuous 150 Vdc 8A turned OFF by adjusting EXC. clockwise to max.
Max. 215 Vdc 10A for 10 secs.
Resistance Min.15 ohms, Max.100 ohms @ 220V Voltage Thermal Drift
Fuse Spec. Slow blow 5 x 20 mm 10A Less than 3% from -
40 to +70 ˚C
External Voltage Adjustment (VR1, VR2) Under-Frequency Knee Point Thermal Drift
Max. +/- 10% @ 1K ohm 1 watt potentiometer Less than +/- 0.1 Hz from -
40 to +70 ˚C
Quadrature Droop Input (S1, S2) Environment
CT N:5A or N:1A (DIP switch setting) Operation Temperature -40 to +60
˚C
Burden : greater than 5VA Storage Temperature -40 to +85
˚C
Sensi/- 7% @ PF +/- 0.5 Relative Humidity Max. 95%
(Can be adjusted through Droop setting) Vibration 5.5Gs @ 60 Hz
Analogue Voltage Input (A1, A2) Dimensions
Input resistance greater than 2K ohms 150.0 (L) x 135.0 (W) x 61.0 (H) mm
Input Range +/- 5 Vdc or 0

10 Vdc
5.91 (L) x 5.31 (W) x 2.40 (H) inch
Sensitivity Max.1 Vdc = 5% change in output voltage
(Can be adjusted through Trim setting) Weight
750 g +/- 2%
Build Up Voltage 1.654 lb +/- 2%
Greater than 5 Vac, 25 Hz residual volts input power
ATTENTION
In order to avoid permanent damage to the AVR confirm that the voltage sensing input setting matches
the generator before use (DIP switches SW5 and SW6)