Kustom PA40BATBT, Quick Start Manual

Page: 7 / 10

40W AC powered with fully charged battery
36W Battery powered
1/8" Headphone/line Level Stereo, mixed mono
Line level 1/4" Un-balanced
Mic XLR Balanced
Line level 1/4" Un-balanced
-56dB Residual Noise, all level controls 0% (minimum)
-52dB Nominal System Noise, all level controls at 50%
+70dB Mic to Speaker Output (CH 1 & 2)
+50dB Line to Speaker Output (CH 1 & 2)
+40dB AUX IN to Speaker Output
Channel EQ (high, low)
Phantom Power
+9V Mic Input
USA/Canada 120VAC/60Hz, 80W nominal
Europe/UK/Australia 230~240VAC/50Hz, 80W nominal
China 220VAC/50Hz, 80W Nominal
Speakers Two 4½" 50W 4 Ohm each
Horn
Power Capacity 40W RMS total system
Frequency Response system 70HZ-20kHz 92dB 1W-1M nominal
Nominal Impedance 2x4 Ohms N ot designed for external speakers
mm/kg 180 (width), 525 (height), 190 (depth), 8.5 kg
Inches/Pounds
1-3/8” 7 (width), 20 ¾ (height), 7½ (depth), 18.8 lb
Output Power
Hum & Noise
Dimensions & Weight
Stand Mount
Bluetooth Module Features.
(Available on PA40BATBT only)
20HZ-20kHz
Actual response is tailored to speaker cabinet for
accurate acoustical response.
Bluetooth 3.0+ERD compliant. T2dBm Class 2 power.
Audio DAC: 94dB SNR.A2DP profile support
Accepted Inputs
One 3½" piezo driver
CH 1
CH 2
PA40BATBT Powered PA Specifications
4kHz and above , 800Hz and below.
Power Requirements
SYNC (IN and OUT) System
Linking Circuit
Both jacks accept a balanced input and send a pre-master volume output mix of
channels. Recommended use: Linking two PW40BAT(BT) together.
System Gain
(Measurements made at 1kHz)
Frequency Response
BATTERY:
IT IS RECOMMENDED THAT THE BATTERY BE RECHARGED AFTER USE TO PROLONG THE BATTERY LIFE.
FREQUENT CHARGING WILL NOT HARM YOUR BATTERY, AND WILL ENSURE THAT THE BATTERY IS FULLY
CHARGED AND READY FOR ITS NEXT USE. STORING BATTERY NOT FULLY CHARGED WILL SHORTEN BATTERY LIFE.
-Always charge for 12 full hours after heavy use.
-The battery does not need to be fully discharged before recharging.
-It is recommended to stop using the unit under battery power when red Battery Level LED is on.
-For best results, recharge the unit as soon as possible after use.
-It is best if the battery is fully charged before storing for long periods of time. Store in a cool, dry place.
How do I stay safe when working with a battery?
Whenever you’re handling or working with a lead-acid battery, consult your vehicle and battery Owner’s Manual for safety
precautions.
In the event of an accident, flush affected area with water, and call a physician immediately.
Lead-acid batteries contain hydrogen-oxygen gases that can be explosive and sulfuric acid that can cause severe burns. To help
avoid risk of danger and injury, observe these precautions when handling or working with a lead-acid battery:
•Wear ANSI* approved safety glasses or goggles and a face shield.
•Wear proper clothing to protect your face, hands, and body.
•Make sure your work area is well-ventilated.
•Never lean over battery while jump-starting, testing, or charging.
•Cigarette, flames, or sparks could cause a battery to explode. Keep all ignition sources away from the battery.
•Remove all hand and wrist jewelry. Jewelry could make an electrical contact and cause severe burns by coming in contact with
the terminals.
•Always shield eyes and face from battery.
•Do not charge or use booster cables or adjust post connections without proper instructions and training.
•KEEP VENT CAPS TIGHT AND LEVEL.
•KEEP OUT OF REACH OF CHILDREN.
*ANSI - American National Standards Institute.