background image

 

 

 

REVISION HISTORY 

REVISION A                                                                                                                             
JULY 1998 
 
 

COPYRIGHT 1998 KURT MANUFACTURING 

 
THIS DOCUMENT IS CONFIDENTIAL AND IS THE PROPERTY OF KURT 
MANUFACTURING. IT MAY NOT BE COPIED OR REPRODUCED IN ANY WAY 
WITHOUT THE EXPRESS WRITTEN CONSENT OF KURT MANUFACTURING. 
KURT MANUFACTURING INTENDS TO AND IS MAINTAINING THE WORK AS 
CONFIDENTIAL INFORMATION. KURT MANUFACTURING ALSO MAY SEEK 
TO PROTECT THIS WORK AS AN UNPUBLISHED COPYRIGHT. IN THE EVENT 
OF EITHER INADVERTENT OR DELIBERATE PUBLICATION, KURT 
MANUFACTURING INTENDS TO ENFORCE ITS RIGHTS TO THIS WORK 
UNDER THE COPYRIGHT LAWS AS A PUBLISHED WORK. THOSE HAVING 
ACCESS TO THIS WORK MAY NOT COPY, USE OR DISCLOSE THE 
INFORMATION IN THIS WORK UNLESS EXPRESSLY AUTHORIZED BY KURT 
MANUFACTURING.  
 
 
 

 
 
 

PLEASE READ AND OBSERVE THE FOLLOWING SAFETY PRECAUTIONS 

FOUND THROUGHOUT THIS MANUAL. 

 
 
 

 

 

CAUTION 

FAILURE TO OBSERVE MAY CAUSE MINOR OR MODERATE PERSONAL 

INJURY OR DAMAGE TO THE EQUIPMENT. 

 
 

CAUTION 

USE CAUTION WHEN HANDING CHIP GUARD MATERIAL. EDGES AND 

CORNERS ARE SHARP AND MAY CAUSE PERSONAL INJURY IF NOT 

HANDLED PROPERLY. 

 

 

 

 

Summary of Contents for CT430


















Reviews: