7
• Use the
icons (B7) and (B8) to change the quantity of coffee. The progress bar shows
the quantity of coffee selected.
• Press the OK icon (B9) again to confirm (or the icon (B6) to cancel the operation).
• Press the ESC (B6) icon (B6) (fig. 18) twice to exit the menu.
The appliance is now reprogrammed with the new settings and is ready.
ADJUSTING THE COFFEE MILL
The coffee mill is preset in the factory and should not require adjusting. However, if after making
the first few coffees you find that delivery is either too fast or too slow (a drop at a time), this can
be corrected by adjusting the grinding adjustment knob (fig. 14).
Important!
The grinding adjustment knob must only be turned when the coffee mill
is in operation.
For slower delivery and creamier coffee, turn one click anticlockwise (finer pre-ground coffee).
For faster delivery (not a drop at a time), turn one click clockwise (coarser pre-ground coffee).
PREPARING COFFEE WITH PRE-GROUND COFFEE
(INSTEAD OF BEANS)
• Press the
(B4) icon (B4) (fig. 8) and select the pre-ground coffee function.
• Extract the machine by pulling it outwards using the handles (fig. 7).
• Lift the central lid, place one measure of pre-ground coffee in the funnel (fig. 19), push the
appliance in then proceed as described in the section “Making coffee using coffee beans”.
N.B.: You can make just one coffee at a time by pressing the
icon (B10) (fig. 12).
• After using the machine with pre-ground coffee, to go back to making coffee using beans,
deactivate the pre-ground coffee function by pressing the
icon (B4) (fig. 8).
NOTE 1: Never introduce pre-ground coffee when the machine is off or it could spread through
the inside of the appliance.
NOTE 2: Never add more than 1 measure, otherwise the appliance will not make the coffee.
NOTE 3: Use the measure provided only.
NOTE 4: Introduce only pre-ground coffee for espresso coffee machines into the funnel.
NOTE 5: If more than one measure of pre-ground coffee is used and the funnel clogs, push the
coffee down with a knife (fig. 21) then remove and clean the brewing unit and machine as de-
scribed in the “Cleaning the brewing unit” section.
DELIVERING HOT WATER
• Always make sure the appliance is ready.
• Make sure the hot water spout is in place (fig. 6). Position a container under the spout.
• Press the
icon (B13) (fig. 20). The appliance displays: “HOT WATER PRESS OK”. Press the
OK icon (B9) again and hot water is delivered from the hot water spout into the container
underneath. (You should not deliver hot water for more than 2 minutes at a time). To inter-
rupt, press the
icon (B13) or the ESC icon (B6).
The appliance stops delivery once the set quantity is reached.
CHANGING THE QUANTITY OF HOT WATER
The machine is set by default to automatically delivery 200 ml of hot water.
To change these quantities, proceed as follows:
• Place a container underneath the cappuccino maker (fig. 5).
• Press the
(B2) to enter the menu (fig. 15) or press the
icons (B7) and (B8) (fig.
2) until “PROGRAM HOT WATER” is displayed.
• Press the OK icon (B9) to confirm.
• Select the required quantity of water by pressing the
icons (B7) and (B8). The pro-
gress bar shows the quantity of water selected.
• Press the OK icon (B9) to confirm (or the ESC icon (B6) to cancel the operation.
• Press the ESC (B6) icon (B6) (fig. 18) twice to exit the menu.
• The appliance is now reprogrammed with the new settings and is ready.
MAKING CAPPUCCINO
N.B.:
Set the quantity of coffee you want to use to make the cappuccino in the “Program
cappuccino” function in the menu.
• Select the taste of the coffee you want to use to make the cappuccino by pressing the
icon (B4).
• Remove the lid of the milk container.
• Fill the container with about 100 grams of milk for each cappuccino to be prepared (fig. 23).
Never exceed the MAX level (corresponding to about 750 ml) marked on the container. You
should ideally use skimmed or semi-skimmed milk at refrigerator temperature (about 5°C).
• Make sure the intake tube is correctly inserted in the rubber washer (fig. 24) then replace
the milk container lid.
• Position the frothed milk regulator (C1) between the words CAPPUCCINO and CAFFELATTE
printed on the milk container lid.
The quantity of froth can be adjusted by moving the regulator towards the word CAF-
FELATTE for a denser froth. Moving it towards the word CAPPUCCINO obtains a less dense
froth.
NO froth
“Denser” froth
frothed milk regulator
“Less dense” froth
• Remove the hot water spout (fig 6) and attach the milk container to the nozzle (fig. 25).
• Position the milk spout as shown in fig. 26 and then place a sufficiently large cup under the
coffee and milk spouts.
• Press the
icon (fig. B12). “CAPPUCCINO” is displayed and after a few seconds, frothed
milk flows out of the milk spout into the cup below. (La fuoriuscita del latte si interrompe
automaticamente). (Delivery stops automatically).
• The appliance delivers coffee.
• The cappuccino is now ready. Sweeten to taste and, if desired, sprinkle the froth with a little
cocoa powder.
NOTE 1: While making cappuccino, the flow of frothed milk or coffee can be interrupted by press-
ing the
icon (B12).
NOTE 2: If the milk in the container finishes while delivering frothed milk, remove the container
and add milk. Reattach and press the
(B12) to request a cappuccino again.
NOTE 3: To ensure the complete cleanliness and hygiene of the milk frother, always clean the
circuits in the milk container lid after making cappuccino.
“PRESS CLEAN!” flashes on the display.
• Place a recipient under the milk spout (fig. 26).
• Press the CLEAN button on the lid (C3) and hold down for at least 5 seconds (fig. 26) to start
the cleaning function.
The appliance displays the message “CLEANING!” above a progressive bar.
You should not release the CLEAN button until the bar is complete indicating that cleaning
is concluded.
When the CLEAN button is released, the function stops.
After cleaning, remove the milk container and place in the refrigerator.
The milk should not be left out of the refrigerator for more than 15 minutes.
NOTE 4: To change the quantity of coffee or frothed milk the appliance delivers automatically
into the cup, proceed as described in the section “Changing the quantity of coffee and milk for
cappuccino”.
CHANGING THE QUANTITY OF COFFEE AND MILK
FOR CAPPUCCINO
The appliance is set by default to automatically deliver a normal cappuccino.
To change these quantities, proceed as follows:
Changing the quantity of milk
• Fill the container with milk up to the maximum level indicated on the container.
• Press the
icon (B2) to enter the menu (fig. 15), then press the
icons (B7) and
(B8) (fig. 2) until “PROGRAM CAPPUCCINO” is displayed.
• Press the OK icon (B9) to confirm. “PROGRAM MILK” is displayed.
• Press the OK icon (B9) again.
