6
USING THE APPLIANCE FOR THE FIRST TIME
• Coffee has been used to factory test the appliance and it is therefore completely normal for
there to be traces of coffee in the mill.
• Customise water hardness as soon as possible following the instructions in the “Setting
water hardness” section.
1. Connect the appliance to the mains supply.
Set the required language.
2. To set the language, use the
icons (B7 and B8) to choose the required language (fig.
2). When the message “PRESS OK TO CHOOSE ENGLISH” is displayed, press the OK icon (B9)
(fig. 3) for 3 seconds until “ENGLISH INSTALLED” is displayed. If you set the wrong language,
follow the instructions in the “Setting the language” section.
If your language is not available, select one from those displayed. The instructions refer to
the English version.
Then follow the instructions displayed:
3. After 5 seconds, the appliance displays “FILL TANK”. Extract the water tank (fig. 4), rinse and
fill with fresh water without exceeding the MAX line. Replace and push as far as it will go.
4. Place a cup under the hot water spout (fig. 5). (If the hot water spout is not inserted, the
appliance displays “INSERT WATER SPOUT”. Attach it as shown in figure 6.
The appliance displays: “HOT WATER PRESS OK”.
Press the OK icon (B9) (fig. 3) and after a few seconds a little water comes out of the spout.
5. The machine now displays “TURNING OFF... PLEASE WAIT” and goes off.
6. Extract the appliance by pulling it out using the handles (fig. 7). Open the lid and fill the
container with coffee beans, then close the lid and push the appliance in.
The coffee maker is now ready for normal use.
Important!
Never introduce pre-ground coffee, freeze dried coffee, caramelised beans
or anything else which could damage the appliance.
N.B.!
When using the appliance for the first time, you need to make 4-5 cups of coffee
and 4-5 cappuccinos before the appliance gives satisfactory results.
N.B.!
Each time you turn the coffee maker on by the ON/OFF switch (A23), it performs a
SELF-DIAGNOSIS cycle and then goes off. To turn it on again, press the ON/OFF button (A7) (fig. 1)
TURNING ON AND HEATING UP
Each time the appliance is turned on, it performs an automatic preheat and rinse cycle which
cannot be interrupted. The appliance is ready for use only after completion of this cycle.
Danger of burns!
During rinsing, a little hot water flows from the coffee spouts.
To turn the appliance on, press the ON/OFF/stand-by button (A7) (fig. 1). The message “HEATING
UP... PLEASE WAIT” is displayed.
When heating is complete, the message changes to “RINSING”;
The appliance is at temperature when the message “MEDIUM CUP NORMAL TASTE” is displayed.
If no icon is pressed within about 2 minutes, the time (if set, see the “Setting the clock” section)
is displayed.
If the time has not been set, the appliance displays the last functions set.
When any icon is pressed, “MEDIUM CUP NORMAL TASTE” is displayed again. The appliance is
ready to make coffee again.
MAKING COFFEE USING COFFEE BEANS
1. The appliance is preset to make coffee with a normal taste. You can also choose coffee
with an extra-mild, mild, strong or extra-strong taste. There is also a pre-ground coffee
option. To choose the required taste, press the
icon (B4) (fig. 8) a number of times. The
required coffee taste is displayed.
2. Place 1 cup under the spouts to make 1 coffee (fig. 9) or 2 cups for 2 coffees (fig. 9). Lower
the spouts as near as possible to the cup for a creamier coffee (fig. 10).
3. Press the
icon (B5) (fig. 11) to select the type of coffee: espresso, small cup, medium
cup, large cup, mug. Now press the
icon (B10) (fig. 12) if you want to make a coffee
and the
icon (B11) (fig. 13) if you want to make 2 coffees. The appliance now grinds
the beans and starts delivering the coffee into the cup.
Once the set amount of coffee has been delivered, the machine stops delivery automatically
and expels the exhausted waste coffee into the waste coffee container.
4. After a few seconds, the appliance is ready for use again.
5. To turn the appliance off, press the ON/OFF/stand-by button (A7) (fig. 1). (Before going off,
the appliance performs an automatic rinse cycle. Take care to avoid scalds).
NOTE 1: If the coffee is delivered a drop at a time or not at all, see the “Adjusting the coffee mill”
section.
NOTE 2: If the coffee is delivered too fast and the cream is not satisfactory, see the “Adjusting the
coffee mill” section.
NOTE 3: Tips for a hotter coffee:
• Proceed as described in the section “Changing and setting menu parameters”, “Rinse” func-
tion.
• Unless preheated, do not use excessively thick cups as they will absorb too much heat.
• Preheat the cups by rinsing them with hot water.
NOTE 4: Coffee delivery can be interrupted at any moment by re-pressing the previously selected
icon which remains lit during the operation.
NOTE 5: As soon as delivery is finished, to increase the quantity of coffee in the cup, just keep
pressing the previously selected icon within 3 seconds after delivery has finished.
NOTE 6: When the appliance displays “FILL TANK”, fill the tank with water or the appliance will
not deliver coffee.
(It is normal for there to be a little water left in the tank).
NOTE 7: After about 14 single (or 7 double) coffees, the appliance displays “EMPTY WASTE COFFEE
CONTAINER”.
Even if not full, the empty waste coffee container message is displayed 72 hours after the first
coffee has been delivered. For the 72 hours to be calculated correctly, the machine must never be
turned off with the main switch in the 0 position.
To clean, open the service door on the front of the appliance by pulling the spout (fig. 16), extract
the drip tray (fig. 17) and clean.
When cleaning, always extract the drip tray completely.
Important!
When extracting the drip tray, the waste coffee container MUST always
be emptied.
If this is not done, the machine may be clogged.
NOTE 8: Never extract the water tank while the machine is delivering coffee.
If it is removed, it will not be possible to make the coffee and the appliance will display “GROUND
TOO FINE ADJUST MILL AND PRESS OK” and then “FILL TANK”. Check the level of water in the tank
and replace in the appliance.
To turn the appliance back on, insert the water spout if not already in place (fig. 6), then press the
OK icon (B9). “HOT WATER PRESS OK” is displayed.
Press the OK icon (B9) within a few seconds and deliver water from the spout for about 30 sec-
onds. When delivery stops, the basic modes are displayed again.
N.B.:
The coffee maker may request the operation to be repeated a number of times until
the air is completely elminated from the hydraulic circuit.
N.B.:
if this operation is not performed correctly or if the machine is turned off, the basic
modes may be displayed, although the problem is in fact still present.
CHANGING THE QUANTITY OF COFFEE IN THE CUP
The appliance is set by default to automatically make the following types of coffee:
• espresso
• small cup
• medium cup
• large cup
• mug
To change the quantity, proceed as follows:
• Press the
icon (B2) to enter the menu (fig. 15). Press the
icons (B7) and (B8) (fig.
2) until “PROGRAM COFFEE” is displayed.
• Press the OK icon (B9).
• Select the type of coffee you want to change by pressing the
icons (B7) and (B8).
• Press the OK icon (B9) to confirm the type of coffee you want to make.
