.
1
150/ 120 mm reduction.
1
Anti-recoil valve.
2
Supports for tubecover.
2
Supports hall.
6
Wall plugs (Ø8 x 40).
6
Long bolts (Ø5 x 45).
4
Wall plugs (Ø6 x 30).
4
Long bolts (Ø4 x 30).
2
Washers (Ø6.4 x Ø18).
2
Washers (Ø6.4 x Ø12).
2
Screws (Ø3.9 x 19).
4
Screws M4 x 12.
2
Clips.
Fig. 1 (Page 39)
On installing the kitchen hood make sure
that the Safety Instructions set out on
page 10 are complied with.
To obtain optimum performance, the external
duct must not be more than FOUR METRES
LONG, have no more than two 90° angles and
its diameter must be at least Ø120.
1) Trace and drill the points for fitting the wall
plugs onto the wall (P) (Ø8 x 40) and (J) (Ø6
x 30). See figure 1.
2) Attach the Supports (O) to the wall using
the long bolts (Q) (Ø5 x 45) and the support
(H) with the long bolts (I) (Ø4 x 30), as in
figure 1.
3) Fit the body of the hood to the support (O)
and level the hood using the long bolts (L) (M4
x 12).
4) Trace the location of the wall plugs (R) (Ø8
x 40), through the inside of the kitchen hood.
5) Take the kitchen hood off.
6) Drill into the wall and fit the wall plugs (R)
(Ø8 x 40).
7) Hang the kitchen hood; tighten the screws
(M) (M4 x 12) with the washers (A3) (Ø6.4 x
Ø12) and the long bolts (S) (Ø5 x 45) with the
washers (T) (Ø6.4 x Ø18).
8) Mount the tubecovers, attaching the lower
one to the support (H) as per the detail in
figure 1. Lift the upper tubecover up to the
desired height and mark its shape on the wall.
Remove the tubecovers.
9) Fit the clips (F) to the support (C).
10) Centre the support (C) around the shape
marked; trace and drill the fixing points for the
wall plugs (E) (Ø6 x 30). Attach the support
(C) with the long bolts (D) (Ø4 x 30).
11) Fit the part (A) if the inner tube (not
supplied) is Ø150 or (A) + (B) if it is Ø120.
12) Attach the inner tube with a clamp (not
supplied) to (A) or (B) as the case may be.
13) Once the inner tube has been fitted, fit the
lower tubecover around the extractor fan
outlet and attach the upper tubecover with the
screws (G) (Ø3.9 x 19).
When exterior gas extraction is not possible,
then the kitchen hood may be set to purify the
air by recycling it through active charcoal
filters.
The active charcoal filters have an active life
of between three to six months, depending on
the individual conditions of use. These filters
cannot be washed nor regenerated. They
must be replaced once their useful life comes
to an end.
Fig. 2 (Page 39)
1) Remove the metal filters.
2) Put the charcoal filters (A) into the lateral
draught section (B) of the motor.
3) Fit the metal filters.
4) Remove the tubecovers (H). Fit the support
(J) in the diffuser (C). Mount the connector
Ø150 (L) in the diffuser base.
5) Use the wall plugs and the previously
installed upper tubecover's support (I) long
bolts (D) (Ø4 x 30) to fix diffuser into the wall
(C).
6) Connect the connector base (L) to the
motor exit via the inner tube (not supplied).
Use clamps (Not supplied). Fit the tubecovers
(H) again.
Installation
EN
G
Accesories supplied
13
Active charcoal filters (Optional)
