18
EN
G
1
150/ 120 mm reduction.
1
Anti-recoil valve.
6
Lock screws (Ø8 x 45).
Fig. 1 (Page 19)
On installing the kitchen hood make sure
that the Safety Instructions set out on page
10 are complied with.
To obtain optimum performance, the external
conduct must not be more than FOUR
METRES long, have no more than two 90°
angles and its diameter must be at least Ø120.
1) Using the support (O) trace and drill the
where the screw-fittings will sit onto the roof (S)
(Ø8 x 45).
2) Screw the support (O) into the roof with the
screw-fittings (S) (Ø8 x 45).
3) Mount the upper chassis (A6) onto the
support (O) using the screws (Q) (M6 x 16).
4) Place the parts (A+B) if the inner tube (not
supplied) is Ø120.
5) Attach the inner tube with a clamp (not
supplied) to (B) or on to the motor's air outlet
vent as the case may be.
6) Introduce the upper tubecover (A8) into the
lower tubecover (A9).
7) Fit the lower (A9) and upper (A8) tubecover
units onto the lower body (A7) and the
decorative parts (U).
8) Mount the whole lower unit to the upper
section, attaching it to the roof using the
screws (A10) (M4 x 12) at the required height.
9) Connect the upper part of the inner tube (not
supplied) to the exit.
10) Raise the upper tubecover (A8) and attach
it to the upper unit with the screws (G) (M4 x
12).
When exterior gas extraction is not possible,
then the kitchen hood may be set to purify the
air by recycling it through active charcoal
filters.
The active charcoal filters have an active life of
between three to six months, depending on
the individual conditions of use. These filters
cannot be washed nor regenerated. They must
be replaced once their useful life comes to an
end.
Fig. 1 (Page 19)
1) Using the support (O) trace and drill the
where the screw-fittings will sit onto the roof (S)
(Ø8 x 45).
2) Screw the support (O) into the roof with the
screw-fittings (S) (Ø8 x 45).
3) Mount the diffuser (A5) with the screws (A4)
(M4 x 12) on to the side rectangles of the upper
body (A6).
4) Mount the upper chassis (A6) onto the
support (O) using the screws (Q) (M6 x 16).
5) Attach the inner tube with a clamp (not
supplied).
6) Introduce the upper tubecover (A8) into the
lower tubecover (A9).
7) Fit the lower (A9) and upper (A8) tubecover
units onto the lower body (A7) and the
decorative parts (U).
8) Mount the whole lower unit to the upper
section, attaching it to the roof using the
screws (A10) (M4 x 12) at the required height.
9) Connect the upper part of the inner tube (not
supplied) to the exit.
10) Raise the upper tubecover (A8) and attach
it to the upper unit with the screws (G) (M4 x
12).
11) Press the glass upwards and carefully
open downwards until the end stop. Remove
the metal filters.
12) Put the filters into the lateral draught
section of the motor making the holes in the
filters match up (A11) with the pivots (A12) of
the motor carcass.
13) Place the metal filters. Bring the glass back
upwards to its initial position and carefully
press for fitting it.
Active charcoal filters (Optional)
Installation
Accesories supplied
All manuals and user guides at all-guides.com
all-guides.com