GWS 307, GKS 324, GKS 644, GKS 954
21
Installation
Installation dimensions
The worktop should be between 30 mm and 40 mm thick. The side clearance
between the hob and wall units must be at least 60 mm. However, for practical
reasons, a clearance of at least approx. 300 mm should be ensured. For flush
installation, please refer to the seperately included assembly instructions „Flush
installation“.
Preparing for installation
–
Cut out the worktop recess as accurately as possible according to the mea-
surements provided with a straight saw blade or a surface milling cutter.
The cut edges should then be sealed so that no moisture can penetrate.
Model GWS 307
–
Remove the appliance from the packaging.
The individual components are separately packed.
Check to ensure that no transport damage has occur-
red prior to installation.
Installing the appliance
–
Prepare the appliance for gas installation according to
the instructions on page 20.
–
Insert the lower part of the hob into the previously-pre-
pared worktop recess.
–
Push the screws (5.1) of all of the clamps (5.2) (for 30
mm worktops turn the clamps (5.2)) to the edge of the
cut-out and tighten them.
–
Remove one of the gaskets (6.7) from the packaging
and put it onto the burner (6.9).
Change the jets if necessary (to modify the hob for a different type of
gas) prior to mounting the glass-ceramic top.
–
Unpack the glass ceramic
hob plate. Adhere the
sealing strip supplied onto
the bottom of the glass-
ceramic top plate so that it
is flush with the edges.
–
Place the glass-ceramic
top onto the worktop so
that the brackets adhered
to the bottom engage in
the lower part of the hob.
It is essential that the
glass-ceramic top is le-
vel on installation: it
must be positioned ca-
refully in the area
around the burner ope-
ning.
–
Put the second gasket
(6.7) and the clamping ring
(6.6) into the opening of
the burner. Position the
clamping ring so that the
holes for the screws lie on the holes for the threads in the burner (6.9).
The clamping ring must be level (it may not be canted)!
–
Use the screws supplied to screw the clamping ring (6.6) to the burner
(6.9). Tighten the screws evenly.
–
Remove the burner components from the packaging and install them one
after the other (see illustration), ensuring that they engage as required.
–
Take the control knobs (6.8) out of the packaging and snap them on.
–
Put on the pan supports (6.1).
Model GKS 324
–
Remove the appliance from the packaging.
The individual components are separately packed. Check to ensure that
no transport damage has occurred prior to installation.
Installing the appliance
–
Prepare the appliance for gas installation according to the instructions on
page 20.
–
Insert the lower part of the hob into the previously-prepared worktop re-
cess.
–
Push the screws (5.1) (see page 21) of all of the clamps (5.2) (for 30 mm
worktops turn the clamps (5.2)) to the edge of the cut-out and tighten them.
Change the jets if necessary (to modify the hob for a different type of
gas) prior to mounting the glass-ceramic top.
–
Remove the glass-ceramic top plate from the packaging. Adhere the sealing
strip supplied onto the bottom of the glass-ceramic top plate so that it is
flush with the edges.
–
Place the glass-ceramic top onto the worktop so that the brackets adhered
294
55
519
min. 60
min. 600
260
500
min. 55
294
55
519
min. 60
min. 600
260
500
min. 55
55
589
519
555
min. 60
500
min. 600
min. 55
889
55
519
min. 60
min. 600
865
500
min. 55
5.1
5.2
5.2
Figure 5
6.1
6.3
6.2
6.7
6.8
6.10
6.9
6.5
6.4
6.7
6.6
Figure 6
