O
PERATION
M
ODES
112-MOBL-3
O
PERATION
M
ODES
The operation modes can be selected using four buttons. The LED above the corresponding button indicates
the selected operation mode. The buttons can be electrically locked via an input (e.g. by connecting an
external key-operated switch), to prevent unauthorised or accidental change of an operation mode. The
operation modes described further down can be activated with these buttons.
A
UXILIARY
D
RIVE
C
ONTROL
A relay with the A
UXILIARY
D
RIVE ON
function (if set) is energised each time before the engine is started.
The indication S
TART
I
NDICATION
flashes. A feedback signal must be sent if starting is enabled (e.g. gas
pipe-tightness confirmed, exhaust gas valve open, pre-lubrication pressure reached). The flashing S
TART
CONTROL
lights steadily (as long as the engine has not fired) and the starter motor can be activated when a
start is enabled.
The input 'S
TARTING
R
ELEASED
' must be permanently connected with the negative potential, if this function
(Enabling of Start) is not required, otherwise the system will not start!
O
PERATION MODE
O
FF
The mode O
FF
is automatically selected when battery voltage is applied (reset function), to prevent an
accidental start-up. When the system is switched to O
FF
from another operation mode:
−
The genset operation is terminated immediately,
−
Any alarms are deleted, except alarms 13 und 14 if their alarm contacts are still activated,
−
The control system is unlocked if no signal is present at the I
MMEDIATE
S
TOP
input.
O
PERATION MODE
M
ANUAL
The auxiliary drives are switched on when the control unit has been switched to M
ANUAL
mode. Pressing the
START button, after the start is enabled by the auxiliary drivers, starts the engine. The generator CB can be
switched on by pressing G
EN
.
ON
(
I
) if the generator voltage is within its limits and no alarm that switches
the generator off is present.
Pressing the G
EN
. O
FF
(
O
) button switches the generator CB off. The generator CB is operated only
manually in this operation mode.
Pressing the On-button has no effect if the voltage of the generator is not within the preset limits. A remote
start command does not cause the generator to be switched on automatically.
Select operation mode O
FF
to shutdown the genset or A
UTO
if there is no automatic start.
Manual Speed Control
The speed can be set manually in the operation modes M
ANUAL
and T
EST
. To do this, select the
SPEED
value
or the G
ENERATOR
L
OAD
in A
CTUAL VALUES
and hold the M
ANUAL
or
T
EST
button down. Press in addition
the buttons [
↑
] and [
↓
] to increase or decrease the speed signal sent to the engine.
Manual Voltage Adjust
The generator voltage can be set manually in the operation modes M
ANUAL
and T
EST
. To do this, select the
display with the G
ENERATOR
V
OLTAGE
in A
CTUAL VALUES
and hold the M
ANUAL
or
T
EST
button down.
Press in addition the buttons [
↑
] and [
↓
] to increase or decrease the voltage control signal sent to the engine.
O
PERATION MODE
A
UTO
The genset is started after a remote start command when the start delay time is up. The auxiliary drives are
switched on and the start sequence is begins when the start is enabled. The F
AIL TO
S
TART
alarm is triggered
and the control unit is blocked if the genset has not started up at the end of the start sequence. The generator
CB is switched on as soon as the genset has run up and the generator voltage and frequency are within their
limits.
A delay time follows (command-off delay) after the remote command is removed. After that, the generator
CB is switched off. To prevent the engine from a heat increase, the generator set will run unloaded for the
configured cooling down period, and then it will be shutdown.
E
XTERNAL
S
TART
C
OMMAND
In this operation mode the genset can be activated by two external start commands:
−
Start with generator operation,
−
Start without generator operation for an easy stand-by.
Operation Modes 112- MOBL-3 / 07-01-25
9 / 18 Changes
without
further
notice
reserved.