Kubota WSM L3540-II Workshop Manual Download Page 122

Page: 122 / 672

ENGINE

L3540-II, L4240-II, L5040-II, L5240-II, L5740-II , WSM

1-S20

CAUTION

• Check the injection pressure and condition after Be carefuling that there is nobody standing in the

direction the fume goes.

• If the fume from the nozzle directly injects the human body, cells may be destroyed and blood poisoning

may be caused.

Nozzle Spraying Condition

1. Set the injection nozzle to a nozzle tester, and check the nozzle

spraying condition.

2. If the spraying condition is not good, replace the nozzle piece.

9Y1211167ENS0013US0

Fuel Injection Pressure

1. Set the injection nozzle to a nozzle tester.
2. Slowly move the tester handle to measure the pressure at which

fuel begins jetting out from the nozzle.

3. If the measurement is not within the factory specifications,

replace the adjusting washer (1) in the nozzle holder to adjust it.

(Reference)

• Pressure variation with 0.025 mm (0.0010 in.) difference of

adjusting washer thickness.
Approx. 590 kPa (6.0 kgf/cm

, 85 psi)

9Y1211167ENS0014US0

Valve Seat Tightness

1. Set the injection nozzle to a nozzle tester.
2. Raise the fuel pressure, and keep at 12.8 MPa (130 kgf/cm

1850 psi) for 10 seconds.

3. If any fuel leak is found, replace the nozzle piece.

9Y1211167ENS0015US0

(a) Good

(b) Bad

Fuel injection pressure

Factory specification

13.8 to 14.7 MPa
140 to 150 kgf/cm

2000 to 2130 psi

(1) Adjusting Washer

Valve seat tightness

Factory specification

No fuel leak at
12.8 MPa
130 kgf/cm

1850 psi

KiSC issued 02, 2015 A

Summary of Contents for WSM L3540-II

































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for WSM L3540-II

Reviews:

Related manuals for WSM L3540-II

Brands by name

Popular brands

Kubota WSM L3540-II, Workshop Manual

Search results

Summary of Contents for WSM L3540-II

Reviews:

Related manuals for WSM L3540-II

Brands by name

Popular brands