background image

INFORMATION

L2501, WSM

I-2

OPERATE SAFELY

• Do not use the machine after you consume alcohol

or medication or when you are tired.

• Put on applicable clothing and safety equipment.
• Use applicable tools only. Do not use alternative

tools or parts.

• When 2 or more persons do servicing, make sure

that you do it safely.

• Do not operate below the machine that only a jack

holds. Always use a safety stand to hold the
machine.

• Do not touch the hot parts or parts that turn when the

engine operates.

• Do not remove the radiator cap when the engine

operates, or immediately after it stops. If not, hot
water can spout out from the radiator. Only remove
the radiator cap when it is at a sufficiently low
temperature to touch with bare hands. Slowly loosen
the cap to release the pressure before you remove it
fully.

• Released fluid (fuel or hydraulic oil) under pressure

can cause damage to the skin and cause serious
injury. Release the pressure before you disconnect
hydraulic or fuel lines. Tighten all connections before
you apply the pressure.

• Do not open a fuel system under high pressure.

The fluid under high pressure that stays in fuel lines
can cause serious injury. Do not disconnect or repair
the fuel lines, sensors, or any other components
between the fuel pump and injectors on engines with
a common rail fuel system under high pressure.

• Put on an applicable ear protective device (earmuffs

or earplugs) to prevent injury against loud noises.

• Be careful about electric shock. The engine

generates a high voltage of more than DC100 V in
the ECU and is applied to the injector.

WSM000001INI0012US0

PREVENT A FIRE

• Fuel is very flammable and explosive under some

conditions. Do not smoke or let flames or sparks in
your work area.

• To prevent sparks from an accidental short circuit,

always disconnect the battery negative cable first
and connect it last.

• The battery gas can cause an explosion. Keep the

sparks and open flame away from the top of battery,
especially when you charge the battery.

• Make sure that you do not spill fuel on the engine.

WSM000001INI0005US0

KiSC issued 09, 2014 A

Summary of Contents for WSM L2501
































Reviews: