Kubota V5008 Installation & Owner'S Manual Download Page 9 | Manualshive

Page: 9 / 15

Kubota V5008 Installation & Owner'S Manual Download Page 9

p. 9 of 15

7.4   Install the blade angle handle. For easiest installa-
      tion, be certain A-frame is oriented as in fig 7.4,
      with the trip frame blade angle slot aligned with the
      A-frame angle slot in the center position.  Orient the
      blade angle handle so that the spring and handle
      point away from the moldboard, per fig.7.4

7.5   Per figs. 7.4 and 7.5, slide blade angle handle and
      spring into blade angle slot, being certain to capture
      lower A-frame plate between the angle handle roll
      pins.

7.6   Per fig 7.6, with a pair of pliers stretch the handle
      spring away from moldboard and engage the spring
      hook into the retaining slot of the upper A-frame
      plate.

7.7   To rotate blade to any of the four possible angled
      positions, pull the handle towards the moldboard
      (away from the front of the vehicle) until the handle
      clears the uppermost blade angle slot.  Rotate the
      plow into the desired position and release the han-
      dle. Be certain the blade angle handle is re-engaged
      in the uppermost slot. Wiggle the moldboard to test
      engagement of the handle.

Fig. 7.6—Blade angle handle installed

Fig. 7.4—Blade angle handle oriented correctly

Blade angle slots.

Align slots in center

position.

Lower A-frame plate

sits between these

roll-pins

Upper roll pin
on top of low-

er A-frame

Lower A-

frame plate

Fig. 7.5—Blade angle handle

Spring retaining

slot

Upper A-

frame plate

«
...
7
8
9
10
11
...
»

Summary of Contents for V5008
















Reviews:

No comments