Kubota V5008 Installation & Owner'S Manual Download Page 10 | Manualshive

Page: 10 / 15

Kubota V5008 Installation & Owner'S Manual Download Page 10

p. 10 of 15

8. Chain/Winch

Shackle

Installation

(for all models)

8.1 Locate the Lift Chain Shackle per figure 8.1

8.2  Per Fig 8.2, slide Lift Chain through shackle then
    insert the clevis pin on the lift chain shackle into the
    lifting hole on the trip frame. Slip cotter pin into
    hole on clevis pin and bend back to lock in place.

9. Blade Marker Installation

(for all models)

9.1 Per fig. 9.1, locate the blade marker kit.

9.2 Per fig 9.2, find the blade marker mounting holes on
    upper portion of the moldboard. Align the holes on
    the blade marker with the holes on the upper corner
    of the moldboard. Install two 5/16” hex head bolts
    and two Nylock hex nuts supplied in the blade mark-
    er kit.  Use a 5/16” washer under the Nylock hex
    nuts.  Repeat step 9.2 to install the blade marker on
    the opposite side of the moldboard.

Fig. 8.1—Lift Chain Shackle

Fig. 8.2—Shackle installed on Trip Frame

Trip Frame

Lifting Hole

Fig. 9.2—Blade Marker Installation

Fig. 9.1—Blade Marker Kit

«
...
8
9
10
11
12
...
»

Summary of Contents for V5008
















Reviews:

No comments