manualshive.com logo in svg

Kubota SQ-1120, Operator'S Manual, Page: 27 / 63

Share
Download
Kubota SQ-1120 Operator'S Manual Download Page 27

PRE-OPERATION CHECK

12

B

Fuel

To avoid personal injury:

A

DO NOT refuel when engine is
running or hot.

A

Always shut off the engine before
refueling.

A

DO NOT overfill fuel system. If any
fuel overflows, wipe it up completely
before starting operation.

A

When refueling, keep all flames,
sparks and cigarettes away from
generator.

1. Always fill the fuel through the fuel tank strainer.
2. Make sure that dirt or water does not enter the fuel

tank.

3. Fill with Diesel fuel No.2-D (ASTMD975).
4. Below 0 C (32 F) a mix of No.1-D and No.2-D is

acceptable.

5. Fuel level is read by fuel gauge placed on the control

panel.
Fuel gauge is activated with the main switch key "ON".

A

If the fuel tank should empty completely causing the
engine to stop, then the fuel system requires air
bleeding after filling the tank and before restarting the
engine.
(See "Air Bleeding the Fuel System" in "PERIODIC
SERVICE" section.)

1G296-8914.book  12 ページ  ２０１２年３月１９日　月曜日　午前１０時４０分

Summary of Contents for SQ-1120
































































Reviews:

No comments