background image

PAGE 2 OF 21 

 

Exposure

 

to

 

Carbon

 

Monoxide

 

can

 

Cause

 

illness,

 

serious

 

injury

 

or

 

death.

 

Never operate vehicle if suspicious of Carbon 

Monoxide. Inspect exhaust system for leaks monthly. Leaks 
can result from loose connections, corrosion, cracks or 
other damage to the exhaust manifold. If leaks are found, 
repair or replace exhaust system. Do not use vehicle until 

This cab is designed and manufac-
tured for use only as reasonable 

weather protection. This cab is not applicable, nor should 
the cab be considered as protection against roll over, col-
lision or other accidents that may result. This cab is 

NOT

 

a

 

R.O.P.S.

 

cab. 

Extreme

 care should be taken when operat-

ing and by qualified, experienced operators only.  

CAB INSTALLATION 
 

BEFORE YOU START 

HELPFUL REMINDERS: 

A. Refer to parts diagram toward the back of this manual to help identify parts during the assem-

bly process.  

B. To assist with the cab installation, leave all bolts loose for later adjustment unless otherwise 

specified. 

C. Read and understand all instructions before beginning. 
D. Plastic washers have been supplied to provide a weather seal under the 

heads of all exterior bolts. The plastic washer should be installed under 
each bolt head directly against the outside cab surface. Care should be 
taken not to over tighten the fasteners and damage the plastic washer. 
Also use metal washers as required. 

E. Apply a clear silicone sealant to seal any minor gaps that may occur 

due to vehicle variations. 

F. Start all bolts by hand to avoid cross threading.

 

 

 
TOOLS REQUIRED: 

           

  

 

Set of standard and metric sockets and open end wrenches 
One 21mm socket with long extension 
One 3/8” and one 1/2” Drive Ratchet 
One 3/16” Allen Wrench 
One large Phillips Head Screwdriver 
Grease 
Electric or cordless drill 
9/32” and 3/8” drill bits 
Tape measure 
Scissors 
Wire Crimp Tool 
Electrical tape 

Fastener 

Cab Surface 

Steel Washer 

Plastic Washer 

WARNING 

WARNING 

NOTICE 

Cabs and accessories add additional weight to the base 
vehicle.  All accessory weights are listed in product bro-
chures.  Deduct the accessory’s total weight from the vehi-
cle’s rated capacity and never exceed the vehicle’s rated 
capacity including driver and passenger 

Summary of Contents for F5205






















Reviews: