manualshive.com logo in svg

Kubota CKTGL11000, Operator'S Manual, Page: 48 / 62

Share
Download
Kubota CKTGL11000 Operator'S Manual Download Page 48

36

PERIODIC SERVICE

ENGL

ISH

[Engine model ··· Z482, D722]

B

Fan Belt

C

Adjusting Fan Belt Tension

CAUTION

To avoid personal injury:

A

Be sure to stop the engine and
remove the key before checking the
belt tension.

A

Be sure to reinstall the detached
safety shield after maintenance or
checking.

1. Stop the engine and remove the key.
2. Apply moderate thumb pressure to belt between

pulleys.

3. If the belt tension is not as specified, loosen the lock

nut and turn the adjust nut to get the belt tension
within the specified range.

4. Tighten up the lock nut.
5. Replace fan belt if it is damaged.

A

If belt is loosen or damaged and the fan is damaged,
it could result in overheating or insufficient charging.
Adjust correctly or replace the belt.

(1) Fuse 3A : External connection terminal block
(2) Fuse 10A : AC (Accessory Line)
(3) Fuse 5A : Glow 
(4) Fuse 15A : Solenoid
(5) Fuse 15A : (spare)
(6) Fuse 10A : (spare)

Proper fan belt tension

A deflection of between 12 to 

14 mm (0.47 to 0.55 in.) when 

the belt is pressed in the middle 

of the span.

(1) Fan belt
(2) Bolt and adjust nut
(3) Lock nut

(A) 12 to 14 mm (0.47 to 0.55 in.)

(under load of 98 N (22.1 lbs.))

Summary of Contents for CKTGL11000































































Reviews:

No comments