background image

15

Section 1: Assembly & Set-up 

4/10/19

AP-SR2672, & AP-SR2690 for Skid Steer Powered Rakes 321-004MK

Table of Contents

Switch & Wire Harness With Eyelets

Figure 1-10

Control Harness With 2 Eyelets

323-097A . . . . . . . . . . . . . SWITCH & WIRE HARNESS

Refer to Figure 1-10:

This switch and wire harness is designed for attaching 
the Powered Rake to a Skid steer without a 2 pin or 14 pin 
Deutsch plug. The 2 push button control switch can be 
placed approximately 9 ft. from the solenoid valve.

1.

Disconnect negative (-) black ground wire from the 
skid steer’s battery post (Not shown).

2.

Attach positive (+) red wire eyelet (A) to a 12 volt 
power source. Tighten fastener hardware.

3.

Attach negative (-) black wire eyelet (B) to ground. 
Tighten fastener hardware.

4.

Reconnect negative (-) black ground wire to the skid 
steer’s battery. Tighten fastener hardware.

5.

The push button control switch (#9) is mounted with 
magnets on the back. Locate and mount this switch 
in a convenient easy to reach location.

6.

Connect power cord (#8) to control switch wire (#7).

7.

Connect green & black wire connector (#1) to the top 
solenoid wire (#2).

8.

Connect red and white wire connector (#3) to the 
bottom solenoid wire (#4). 

9.

Continue with 

“Operational Check” 

on this page.

Solenoid Valve

37140

Green Wire

Red Wire

Positive (+) 
Red Wire

Negative (-) Black Wire

NOTE:  

Additional zip ties may be needed to 

properly secure all wiring harness. Customer to 
supply and locate all additional zip ties.

Operational Check

Refer to Figure 1-7 or Figure 1-10: 

1.

With hydraulics hooked-up, start skid steer and press 
buttons to angle broom to sweep material to the right 
and left.

2.

If broom angles in opposite direction desired, switch 
plugs (#1 & #3) with solenoid wires (#2 & #4).

3.

If everything is working correctly, secure 
harness (#6) near the solenoid valve with zip tie (#5).

4.

Make certain hydraulic hoses from skid steer to 
broom are kept away from all pinch points. 

5.

Tie hydraulic hoses and electrical cables together 
12" and 29" away from quick release couplers with 
zip ties (#5).

Summary of Contents for AP-SR2672





































Reviews: