KTM F9903SE, Setup Instructions

Page: 20 / 25

4 TECHNICAL DATA
18
4.1 Chassis tightening torques
Remaining screws, chassis EJOT PT ® K50x12 1 Nm (0.7 lbf ft)
Remaining screws, chassis
EJOT PT ®
K50x14 1 Nm (0.7 lbf ft)
Remaining screws, chassis EJOT PT ® K50x16 2 Nm (1.5 lbf ft)
Remaining screws, chassis EJOT PT ® K50x18 2 Nm (1.5 lbf ft)
Remaining screws, chassis EJOT PT ® K45x12 1 Nm (0.7 lbf ft)
Screw, air filter box cover EJOT PT ® K60x30 2 Nm (1.5 lbf ft)
Screw, exhaust valve cover fasten-
ing EJOT SF ® M4x6
‑
K 4 Nm (3 lbf ft)
Screw, tail light EJOT PT ® K50x14 2.5 Nm (1.84 lbf ft)
Screw, combination switch, left M4 5 Nm (3.7 lbf ft)
Screw, side stand switch M4 2 Nm (1.5 lbf ft)
Remaining nuts, chassis M5 5 Nm (3.7 lbf ft)
Remaining screws, chassis M5 5 Nm (3.7 lbf ft)
Screw, cable channel M5 5 Nm (3.7 lbf ft)
Screw, chain sliding guard M5 5 Nm (3.7 lbf ft)
Screw, combination switch, right M5 5 Nm (3.7 lbf ft)
Screw, cornering light M5 2 Nm (1.5 lbf ft)
Screw, fuel level sensor M5 3 Nm (2.2 lbf ft)
Screw, fuel tank filler cap M5 3 Nm (2.2 lbf ft)
Screw, trim M5x12 3.5 Nm (2.58 lbf ft)
Swing angle sensor screw M5x16 5 Nm (3.7 lbf ft)
Loctite ® 243™
Cable disk nut, exhaust valve con-
trol unit M6 14 Nm (10.3 lbf ft)
Ground fitting on frame M6 10 Nm (7.4 lbf ft)
Nut, ABS module fastening M6 8 Nm (5.9 lbf ft)
Nut, cable on starter motor M6 4 Nm (3 lbf ft)
Nut, exhaust valve control unit
throttle cable M6 5 Nm (3.7 lbf ft)
Remaining nuts, chassis M6 10 Nm (7.4 lbf ft)
Remaining screws, chassis M6 10 Nm (7.4 lbf ft)
Screw, ABS module fastening M6 5 Nm (3.7 lbf ft)
Screw, angle sensor cover M6 6 Nm (4.4 lbf ft)
Loctite ® 243™
Screw, ball joint of push rod on
foot brake cylinder M6 5 Nm (3.7 lbf ft)
Loctite ® 243™
Screw, battery terminal M6 4.5 Nm (3.32 lbf ft)
Screw, clutch assembly M6 5 Nm (3.7 lbf ft)
Loctite ® 243™
Screw, connecting piece, rear
brake line M6 10 Nm (7.4 lbf ft)
Loctite
®
243™
Screw, cooler retaining bracket M6 7 Nm (5.2 lbf ft)
Screw, exhaust clamp on main
silencer M6 8 Nm (5.9 lbf ft)
Screw, exhaust clamp on manifold M6 8 Nm (5.9 lbf ft)