KTM 1998 50 SXR Adventure Owner'S Handbook Manual Download Page 23

ENGLISH

21

TECHNICAL SPECIFICA

TIONS - CHASSIS    50 SXR  Adventure, Pro Junior

, Pro Senior ‘98

Adventure

Pro Junior

Pro Senior

Frame

single downtube, split-cradle

Fork

telescopic fork (Paiolo) 

Wheel travel front/rear

140/160 mm (5.5/6.3 in)

140/160 mm (5.5/6.3 in)

165/170mm (6.5/6.7 in)

Rear suspension

central shock absorber (Paioli)

Front brake

internal expanding, single/cam drum brake  Ø 90 mm (3.5“)

Rear brake

internal expanding, single/cam drum brake  Ø 90 mm (3.5“)

Tyres 

front / rear: Cheng Shin 2.50x10“  C-755

Air pressure

front / rear: 1.0 bar (14 psi) / 1.0 bar (14 psi)

Fuel tank capacity

2.9 liter (0,75 USgal)

Final drive ratio

10 : 45 t

11 : 45 t

Chain 

1/2 x 3/16" (415) 94 rolls

1/2 x 3/16" (415) 102 rolls

Steering angle

63°

Wheel base

910 mm (35.8 in)

1030 mm (40.5“)

Seat height, unloaded

5

85 / 610 mm (23 / 24 in) (adjustable)

650 / 675 mm (25.6 / 26.6 in) (adjustable)

Ground clearance

230 mm (9.05 in)

255 mm (10“)

Dead weight without fuel

39 kg (86 lbs)

39.5 kg (87.2 lbs)

40.5 kg (89.4 lbs)

Rider’s body height

max. 130 cm (51 in)

Rider’s body weight

max 35 kg (78 lbs)

Recommended age of rider

4 to 6 years

7 to 8 years

Engine

S5-E

S5-GS

Adventure

Pro Junior

Pro Senior

Spring

2,55 N/mm

2,55 N/mm

2,55 N/mm

Spring preload

10 mm (0.4 in)

20 mm (0.8 in)

20 mm (0.8 in)

Capacity per fork leg

––

ca 150 ccm

ca 160 ccm

Fork oil

––

SAE

7.5

SAE 7.5

STANDARD-ADJUSTMENT – FORK

Hexagon nuts front axle

M 12x1

30 Nm (22 ft.lb)

Hexagon nuts rear axle

M 12x1

30 Nm (22 ft.lb)

Hexagon nut swing arm bolt

M 10

20 Nm (15 ft.lb)

Clamping screw upper fork bridge

M 8

15 Nm (11 ft.lb)

Clamping screw lower fork bridge

M 8

15 Nm (11 ft.lb)

Other screws chassis

M 6

10 Nm (7 ft.lb)

M 8

25 Nm (18 ft.lb)

M 10

50 Nm (37 ft.lb)

TIGHTENING TORQUES

Summary of Contents for 1998 50 SXR Adventure

























Reviews: