KTI Networks KGS-2422 Installation Manual Download Page 21 | Manualshive

Page: 21 / 32

KTI Networks KGS-2422 Installation Manual Download Page 21

2.10 Making SFP Fiber Connection

The dual-speed SFP slot must be installed with an SFP fiber transceiver for making fiber connection. Your

switch may come with some SFP transceivers pre-installed when it was shipped.

Since the SFP slot is dual-speed support, it may be installed with a 1000M SFP fiber transceiver or a 100M

SFP fiber transceiver. Choose a right transceiver which matches the requirements for connection speed, fiber

type and connection distance for your application.

Installing SFP Fiber Transceiver

To install an SFP fiber transceiver into SFP slot, the steps are:

1. Turn off the power to the switch.

2. Insert the SFP fiber transceiver into the SFP slot. Normally, a bail is provided for every SFP transceiver.

Hold the bail and make insertion.

3. Until the SFP transceiver is seated securely in the slot, place the bail in lock position.

Connecting Fiber Cables

LC connectors are commonly equipped on most SFP transceiver modules. Identify TX and RX connector

before making cable connection. Plug in the cables as shown below. Make sure RX-to-TX connection rule is

followed between two ends of the connected cable.

-21-

«
...
19
20
21
22
23
...
»

Summary of Contents for KGS-2422

































Reviews:

No comments