manualshive.com logo in svg

KTI Networks KGS-2422, Installation Manual, Page: 11 / 32

Share
Download
KTI Networks KGS-2422 Installation Manual Download Page 11

-11- 

1000M 

Port speed 1000Mbps status 

Link/Act. 

Port link and activity status (Port 1 – Port 24) 

 

1.5 Specifications 

10/100/1000 Copper Ports 

Compliance 

IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX, IEEE 802.3u 1000Base-T 

Connectors 

Shielded RJ-45 jacks 

Pin assignments 

Auto MDI/MDI-X detection 

Configuration 

Auto-negotiation or software control 

Transmission rate 

10Mbps, 100Mbps, 1000Mbps 

Duplex support 

Full/Half duplex 

Network cable 

Cat.5 UTP 

 

Dual-speed SFP Slots 

Compliance 

IEEE 802.3z 1000BASE-SX/LX (mini-GBIC) 

 IEEE 

802.3u 

100BASE-FX 

Connectors 

SFP slot supports optional both 100M and 1000M SFP type fiber transceivers 

Configuration options 

Auto-negotiation 1000Mbps Full duplex   

Forced 100Mbps Full duplex 

 (Software 

configurable) 

Network cables 

MMF 50/125

μ

m 60/125

μ

m, SMF 9/125

μ

m 

Eye safety 

IEC 825 compliant 

 

Fixed 100M Fiber Ports 

Compliance IEEE 

802.3u 

100BASE-FX 

Connector options 

Duplex SC for multimode fiber 

 

Duplex SC for single mode fiber 

 

Duplex ST for multimode fiber 

 

BiDi SC for single SM fiber 

Configuration 

100Mbps, full duplex 

Network cables 

MMF 50/125

μ

m 60/125

μ

m, SMF 9/125

μ

m 

Eye safety 

IEC 825 compliant 

 

Console Port 

Interface 

RS-232, DTE type 

Connector 9-pin 

D-sub 

Summary of Contents for KGS-2422

































Reviews:

No comments