KTI Networks KFC-241 Installation Manual Download Page 25

Page: 25 / 25

-25-

Appendix. On-board Configuration

Six configuration jumpers are provided on the internal PC board of the device. They can be used to change the
configuration and adapt the device for some special applications. The jumpers are inaccessible by users.

Jumper Settings

OFF

Auto-negotiation (factory default)

JP1

TP auto mode

ON Forced

mode

OFF

Full duplex (factory default)

JP2 TP

duplex

ON Half

duplex

OFF

100Mbps (factory default)

JP3 TP

speed

ON 10Mbps

OFF

Enabled (factory default)

JP4

Link Fault Pass Through

ON Disabled

OFF

Smart-mode (factory default)

JP5 Forward

mode

ON Store-and-forward

always

OFF Enable

(factory

default)

JP6 802.3x

ON Disable

Note: Only the factory-authorized engineers are allowed to change the settings of the jumpers.

Summary of Contents for KFC-241


























Search results

Summary of Contents for KFC-241

Reviews:

Related manuals for KFC-241

Brands by name

Popular brands

KTI Networks KFC-241, Installation Manual

Search results

Summary of Contents for KFC-241

Reviews:

Related manuals for KFC-241

Brands by name

Popular brands