background image

This equipment has been tested and found to comply with the limits for a Class A digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference in a residential installation. This equipment generates, uses and can 
radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications.  However, there is no guarantee that 
interference will not occur in a particular installation. If this equipment does cause harmful interference 
to radio or television reception, which can be determined by turning the equipment off and on, 
the user is encouraged to try to correct the interference by one of the following measures:

* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the receiver 
   is connected.
* Consult the dealer or an experienced radio/TV technician for help.

Federal Communication Commission Interference Statement

3

ATTENTION!  This is a class A product which may cause radio interference in a domestic 
environment; in this case, the user may be urged to take adequate measures.

This Product is RoHS compliant.

Your KT&C product is designed and manufactured with high quality materials 
and components which can be recycled and reused.This symbol means that 
electrical and electronic equipment, at their end-of-life, should be disposed 
of separately from your household waste.Please, dispose of this equipment 
at your local community waste collection/recycling centre.In the European 
Union there are separate collection systems for used electrical and electronic 
product.

The information in this manual was current upon publication.  The manufacturer reserves the right to revise 
and improve his products. Therefore, all specifications are subject to change without prior notice. Misprints 
reserved. Please read this manual carefully before installing and using this unit. Be sure to keep it handy for 
later reference

WEE

FCC Caution:

  Any changes or modifications not expressly approved by the party responsible for compliance 

                         could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 

(1)

 This 

device may not cause harmful interference

 

(2)

 this device must accept any interference received, including 

interference that may cause undesired operation.

Summary of Contents for KPC-N635NH10














Reviews: