Installation Sheet
KSR98204 Sensor Set Up Guide
Read these instructions before commencing installation. Please give these instructions to the owner/occupier after
installation to retain for future reference/maintainence.
Navara HBX
Available finish: Black Finish
LED Highbay
IP20
Drg No. KSR98204-IS-A
KSR Lighting Ltd, Unit E Hazleton Interchange, Lakesmere Road, Horndean, Hampshire, PO8 9JU
KSR Lighting Aftersales: 023 92 674343
E-mail: [email protected]
22.03.2022RTG
ON/
OFF
Auto Mode
Reset
+
-
Test
2s
30s
1min
10min 30min
5min
Permanent On/Off function
This button turns the Light ON or OFF and disables
the sensor. To change this setting Press 'Auto Mode',
'RESET' or 'Scene Mode'.
Auto Mode
Pressing this button activates the sensor and reverts
all settings to those selected before the light was
switched ON/OFF
Reset Function
By pressing the RESET button, all settings made with
the remote are removed.
Dim +/-
Press and hold + or - to adjust the brightness between
10% and 100% during the Standby Period
Test Mode
Press this button to enter Test Mode.
In test Mode Hold time is reduced to 2 seconds.
The Stand-by Period and Daylight Sensor is disabled.
Exit Test Mode by pressing 'RESET'
or any 'Scene mode' or 'Hold Time' Button.
Detection Range
Press this button to reduce sensitivity
Standby Dimming Level
Use these buttons to set your desired dimming
level during the Standby period.
Hold Time (Hold Period)
Use these buttons to set the duration of the Hold Period
100%
50%
10%
0s
10s
1min
10min 30min
+
10%
20%
30%
Standby Period
Use these buttons to set the duration of the Standby
Period
Power Output
These button switches output of the luminaire
between 80% and 100%. This makes it possible to
conserve power in rooms or areas where 80%%
output is sufficient.
Lux Control
Use these buttons to set your desired threshold for
the daylight sensor function. When the ambient level
of natural light is less than your selected level, the
fitting will turn ON.
Lux Disable
Press this button to disable the built-in daylight
sensor. Once disabled, the sensor will activate the
light when someone is present, regardless of the
amount of ambient light.
Daylight Sensor Threshold
Press this button to set the lux value currently
measured by the sensor as the new threshold for the
daylight sensor. This replaces the previous setting. If
the amount of ambient light exceeds this threshold,
the luminaire will not turn ON.
Scene Mode
For SC1-SC4 you can choose between these
alternative settings
Power
100%
Power
80%
2Lux 10Lux 50Lux
Lux
Disable
SC1
SC3
SC2
SC4
Auto Mode
ON/
OFF
Reset
SC1
SC3
SC2
SC4
100%
50%
10%
10%
20%
30%
2Lux
10Lux
50Lux
Lux
Disable
30s
1min
10min
30min
5min
Test
2s
0s
10s
1min
10min 30min
M/A
+
Power
100%
Power
80%
+
-
Scene Mode
Dim
Detection range
Stand-by dimming level
Hold-time
Stand-by period
Daylight Sensor
Detection
Range
Hold
Time
Standby
Period
Standby
Dim Level
Daylight
Sensor
100%
100%
100%
100%
1 min
5 min
10 min
10 min
10 min
10 min
30 min
+
10%
10%
10%
10%
2 Lux
2 Lux
10Lux
50Lux
