background image

EN

3

FUNCTIONS

• Display of system status

• Display of functioning parameters ( date/time, active GSM network, GSM level, etc)

• System commands (complete or partial arming, reset, activation of outputs terminals, phone calls,

etc.)

• Full Programming of system parameters

• Programming of local parameters (audio volume, backlight levels)

• KP functionality exclusion for front cleaning purposes

• Remote Listening

• Vocal messages recording

• RFID/NFC

 Tag reading to arm and disarm the intrusion detection systems set up with the 

lares

 

devices.

OPTIONALS

KSI7500000.000

 / KIT 1,5 m. cable for GSM/GPRS programming

KSI2100001.300

 / Table sustainer

KSI2100002.300

 / KIT 

ergo

 keypad

INSTALLATION

BUILT-IN INSTALLATION (WITH DIN 503 BOX) OR DIRECTLY ON THE WALL

INSTALLATION WITH TABLE SUSTAINER

The keypad 

ergo

 can be installed directly on a wall or put in an DIN 503 box set in the wall or leant on a 

plain surface by means of the proper sustainer.

1. Push the cable through to the proper opening.

2. Fix the keypad base to the DIN 503 box with the supplied screws opening the proper eyelets. To fix

the keypad base directly to a wall, use proper plugs (not supplied) through the proper eyelets.

3. Connect the cables to the terminals on the rear of the keypad.

4. Fit in the PCBA on the left side of the keypad base, keeping the display in the front and the clamps

on the back, then press the right side until a double-click is heard.

5. Insert a coloured Lexan at choice into the cover.

6. Close the cover properly.

1. Install, with a light pressure, the part 1 of the table sustainer on the back of the keypad base.

2. Fit in the part 2 of the sustainer on the part 1 by the mean of the proper hinge.

3. Push the cable through to the proper opening.

4. Connect the cables to the terminals on the rear of the keypad.

5. Fit in the PCBA on the left side of the keypad base, keeping the display in the front and the clamps

on the back, then press the right side until a double-click is heard.

6. Insert a coloured Lexan at choice into the cover.

7. Close the cover properly.

8. Use the optional cable for the programming of the communicator GSM/GPRS 

gemino

.

Summary of Contents for ergo











Reviews: