KSB Magnochem-Bloc Installation & Operating Manual Download Page 51

Page: 51 / 96

7 Servicing/Maintenance

51 of 96

Magnochem-Bloc

7.4 Dismantling the pump set

7.4.1 General information/Safety regulations

DANGER

Strong magnetic field in the area of the magnetic coupling or the individual
magnets

Danger of death for persons with pacemaker!

Interference with magnetic data carriers, electronic devices, components and
instruments!

Uncontrolled magnetic attraction forces between magnet-equipped components,
tools or similar!

▷

Keep a safety distance of at least 0.3 m.

▷

Also observe the additional instructions. (

Section 2.10, Page 12)

WARNING

Hot surface

Risk of injury!

▷

Allow the pump set to cool down to ambient temperature.

WARNING

Unqualified personnel performing work on the pump (set)

Risk of injury!

▷

Always have repair work and maintenance work performed by specially trained,
qualified personnel.

WARNING

Improper lifting/moving of heavy assemblies or components

Personal injury and damage to property!

▷

Use suitable transport devices, lifting equipment and lifting tackle to move
heavy assemblies or components.

Observe the general safety instructions. (

Section 7.1, Page 44)

For any work on the motor, observe the instructions of the motor manufacturer
(refer to manufacturer's technical product literature).

For dismantling and reassembly observe the exploded views and the general
assembly drawing. (

Section 9.1, Page 79)

In the event of damage, you can always contact our service departments.

DANGER

Insufficient preparation of work on the pump (set)

Risk of injury!

▷

Properly shut down the pump set. (

Section 6.1.7, Page 38)

▷

Close the shut-off elements in the suction line and discharge line.

▷

Drain the pump and release the pump pressure.

▷

Shut off any auxiliary feed lines.

▷

Allow the pump set to cool down to ambient temperature.

Summary of Contents for Magnochem-Bloc

































































































Search results

Summary of Contents for Magnochem-Bloc

Reviews:

Related manuals for Magnochem-Bloc

Brands by name

Popular brands

KSB Magnochem-Bloc, Installation & Operating Manual

Search results

Summary of Contents for Magnochem-Bloc

Reviews:

Related manuals for Magnochem-Bloc

Brands by name

Popular brands