KSB HPK-L Installation & Operating Manual Download Page 28

Page: 28 / 74

5 Installation at Site

28 of 74

HPK-L

1136.8/15-EN

Fig. 13:

Quench connections

24A

Quench outlet

24E

Quench inlet

For pump sets with two mechanical seals in tandem arrangement, connect an
unpressurised quench liquid supply to the "Quench outlet" (24E) and "Quench
inlet" (24A) connections.

5.4 Enclosure/insulation

DANGER

An explosive atmosphere forms due to insufficient venting

Explosion hazard!

▷

Never close or cover the perforation of the bearing bracket guards (e.g. by
insulation).

WARNING

The volute casing and casing/discharge cover take on the same temperature as the
fluid handled

Risk of burns!

▷

Insulate the volute casing.

▷

Fit protective equipment.

CAUTION

Heat build-up in the bearing bracket

Damage to the bearing!

▷

Never insulate the bearing bracket, bearing bracket lantern and casing cover.

5.5 Checking the coupling alignment

DANGER

Inadmissible temperatures at the coupling or bearings due to misalignment of the
coupling

Explosion hazard!

Risk of burns!

▷

Make sure that the coupling is correctly aligned at all times.

Summary of Contents for HPK-L











































































Search results

Summary of Contents for HPK-L

Reviews:

Related manuals for HPK-L

Brands by name

Popular brands

KSB HPK-L, Installation & Operating Manual

Search results

Summary of Contents for HPK-L

Reviews:

Related manuals for HPK-L

Brands by name

Popular brands