KSB BOAX-B Installation & Operating Manual Download Page 10

Page: 10 / 50

3 Transport/Storage/Disposal

10 of 50

8417.8/20-EN

3 Transport/Storage/Disposal

3.1 Checking the condition upon delivery

1. On transfer of goods, check each packaging unit for damage.

2. In the event of in-transit damage, assess the exact damage, document it and

notify KSB or the supplying dealer and the insurer about the damage in writing
immediately.

3.2 Transport

DANGER

The valve could slip out of the suspension arrangement

Danger to life from falling parts!

▷

Only transport the valve in the specified position.

▷

Never attach lifting accessories to the handwheel.

▷

Observe the information on weights, centre of gravity and fastening points.

▷

Observe the applicable local accident prevention regulations.

▷

Use suitable, permitted lifting accessories, e.g. self-tightening lifting tongs.

▷

For valves with actuators observe the relevant actuator operating manual.
Transport aids on the actuator are not suitable for suspending the entire valve/
actuator assembly.

To transport the valve, suspend it from the lifting tackle as illustrated.

Fig. 1:

Transporting a valve with actuator in a vertical position

Fig. 2:

Transporting a valve with actuator in a horizontal position

Summary of Contents for BOAX-B



















































Search results

Summary of Contents for BOAX-B

Reviews:

Related manuals for BOAX-B

Brands by name

Popular brands

KSB BOAX-B, Installation & Operating Manual

Search results

Summary of Contents for BOAX-B

Reviews:

Related manuals for BOAX-B

Brands by name

Popular brands