Krups EA89 Series, Manual

Page: 19 / 42

17
EN
Automatic cleaning programs
Automatic cleaning program of the coffee circuit
A message on the screen will indicate when a cleaning program needs to be run for the appliance.
To run this cleaning program, you will need a container which holds at least 0.6 l, and which should be placed
beneath the coffee outlets and the steam nozzle, and a KRUPS cleaning tablet. Fig. 37. Carefully follow the
instructions given on the screen. It is also possible to run a cleaning cycle via the Maintenance menu.
!
Important: You do not have to run the cleaning program as soon as the appliance requests it, but it must be
done reasonably soon after. If cleaning is postponed, the alert message will remain illuminated until
the process is completed.
The automatic cleaning program comprises two phases: a cleaning cycle and a rinsing cycle, and lasts about 13
minutes.
!
Important: If you unplug your machine during the cleaning cycle, or if there is a power failure, the cleaning
program will continue from the current phase when the power is returned. It is not possible to
postpone this process. This is essential to ensure that the water circuit has been correctly rinsed. In
this case, a new cleaning tablet may be necessary. Complete the full cleaning program in order to
remove all of the cleaning product which is harmful to health.
Cleaning the “One Touch Cappuccino” block
To complete a cleaning program, you will require two containers (minimum 0.6 L) and KRUPS cleaning liquid.
You can start the cleaning cycle by pressing button
.
Then selecting “Maintenance”

“Milk Cleaning”. Follow the instructions on the screen.
Dismantling the “One Touch Cappuccino” block
In addition to rinsing, it is necessary to clean the different elements of the block every time after using. To dismantle
the block, follow the following instructions:
Remove the milk tube, Fig. 21.
Remove the front lid of the coffee milk nozzles. Slide it downwards and pull it towards you. Fig. 22.
Remove the “One Touch Cappuccino” block by pulling the upper part of the block and pull the orange cleaning tool.
Fig. 23.
Completely dismantle the block. Fig. 24.
Remove the milk tube connector Fig. 27.
Clean all of the dismantled parts (block, connector and milk tube) with soapy water. Then rinse them in hot water.
Fig. 28-30.
Once the elements are clean and dry, assemble the block and return them to their original position. Don’t forget to
return the orange cleaning tool to its original position. Fig. 32-34.
Replace the font lid of the block. Fig. 34. Replace the connector in the milk tube Fig 35 (opposite side of the bevelled
side) and plug in the block. Fig. 36.
Automatic descaling program of the steam circuit
Warning:
if your appliance is fitted with our Claris - Aqua Filter System cartridge, remove the cartridge before
descaling.
A message on the screen will indicate when a descaling program needs to be run for the appliance. The frequency
of this program depends on the quality of the water used and on whether a Claris Aqua Filter System filter is used or
not (the harder the water, the more often the appliance has to be descaled).
!
Important: You are not obliged to carry out this program immediately the appliance requests it, but it must be
carried out reasonably soon afterwards. If descaling is postponed, the alert message will continue to
be displayed until the process is completed.
When the descaling alert level is reached and displayed, press to run the descaling program. To delay it, press
.
Once the procedure has been launched, follow the instructions provided on the screen. It is also possible to run a
descaling cycle via the “Maintenance” menu

“Descaling”.
To carry out a descaling program, you will require a container with a capacity of at least 0.6 L which should be placed
beneath the One Touch Cappuccino block and a KRUPS descaling sachet (40 g). Fig. 37
Fill the water tank up to the CALC mark then pour in the contents of one sachet of descaler.
The descaling program comprises three phases: a descaling cycle and two rinsing cycles. The program lasts
approximately 20 minutes.
!
Important: If there is a power failure or if you unplug your machine, the cycle will continue from the current
phase when the power is returned. It will not be possible to cancel this operation. Complete the full
cycle in order to remove all of the descaling product which is harmful to health.