manualshive.com logo in svg

Kronos H-46 Series, Operation, Safety And Spare Parts Manual

Share
Download
Kronos H-46 Series Operation, Safety And Spare Parts Manual Download Page 19

-A14-

5.10.2    SUSPENSION HOOK 

The tool could be equipped with a suspension hook(H46-50300). The hook must be 

fixed to the tool by two screws (included) in vertical or horizontal position

5.11 Change strap width 

Strap stop (Front) 

(#3) 

Strap stop (Rear) 

(#9) 

H-46A-12

H46-10610 

H46-12510 

H-46A-16/H-46B-16

H46-10600 

H46-12500 

H-46B-19

- 

- 

5.11.1  Remove battery from tool. Remove three screws #6. 

        5.11.2  Remove End Cover #5. 

        5.11.3    Remove screw #4 and strap stop(front) #3. Install the selected strap stop. Tighten the 

screw #4 after applying sealants such as Loctite222.   

5.11.4    Remove screw #10 and strap stop(front) #9. Install the selected strap stop. Tighten the 

screw #10 after applying sealants such as Loctite222.   

5.11.5    Fit end cover #5, Tighten the screw #6 after applying sealants such as Loctite222. 

Summary of Contents for H-46 Series















































Reviews:

No comments

Brands by name

Popular brands

Load more brands