Kromschroder BCU 465 Technical Information Download Page 1

Page: 1 / 31

URNER

ONTROLS

BCU 465

Technical Information

T-Product 2006 April

Automatic burner control unit with integrated igni-

tion transformer packaged in a single compact

metal housing (IP 54/NEMA 3 rating)

For use with direct spark ignited burners
For continuous operation
For use with modulating or frequency ﬁred control

systems

Includes air valve control
Optional proof of closure switch (POC) control input
Optional digital input for 1,400 °F auto ignition lockout
Displays program status, unit parameters, fault

code or ﬂame signals

Optional optical interface for diagnostic information

and parameter settings

Manual mode for burner adjustments and trouble-

shooting

Select restart or immediate fault lockout in the

event of a ﬂame failure

Removable bottom mounting plate with ﬁve (5)

½" conduit openings make installation of electrical

connections simple

Removable terminal blocks to facilitate electrical

ﬁeld wiring

Meets NFPA 86 standard
CE certiﬁed models available

Summary of Contents for BCU 465
































Search results

Summary of Contents for BCU 465

Reviews:

Related manuals for BCU 465

Brands by name

Popular brands

Kromschroder BCU 465, Technical Information

Search results

Summary of Contents for BCU 465

Reviews:

Related manuals for BCU 465

Brands by name

Popular brands