KROHNE TT 51 Series Handbook Download Page 6

Page: 6 / 56

SAFETY INSTRUCTIONS

TT 51 SERIES

www.krohne.com

08/2015 - 4000754203 - MA TT 51 R03 en

1.2 Certifications

1.2.1 EC directive compliance

The device fulfils all applicable statutory requirements of the following EC directives:

•

EMC Directive 2014/30/EU

•

Devices for use in hazardous areas: ATEX Directive 2014/34/EU

The manufacturer certifies successful testing of the product by applying the CE marking.

1.2.2 Ex approvals

TT 51 C (intrinsically safe)

TT 51 R (intrinsically safe)

1.2.3 SIL certification

•

Compliance: functional safety acc. to IEC 61508 part 1 to 3

•

Safety Integrity Level: SIL 2

CE marking

ATEX:

KIWA 14 ATEX 0004X

II 1G Ex ia IIC T6...T4 Ga

IECEx:

IECEx KIWA 14.0002X

Ex ia IIC T6...T4 Ga

ATEX:

KIWA 14 ATEX 0024X

II 2(1)G Ex ia [ia Ga] IIC T6...T4 Gb

IECEx:

IECEx KIWA 14.0011X

Ex ia [ia Ga] IIC T6...T4 Gb

INFORMATION!

For details please refer to the separate SIL documentation.

MA_OPTITEMP_TT_51_en_150828_4000754203_R03.book Page 6 Friday, August 28, 2015 10:54 AM

Summary of Contents for TT 51 Series

























































Search results

Summary of Contents for TT 51 Series

Reviews:

Related manuals for TT 51 Series

Brands by name

Popular brands

KROHNE TT 51 Series, Handbook

Search results

Summary of Contents for TT 51 Series

Reviews:

Related manuals for TT 51 Series

Brands by name

Popular brands