KRESS KUC35, Manual

Page: 12 / 80

12
EN
ASSEMBLY
Note: Always power off the tool and remove the
battery pack before performing any assembly
operations on the tool.
Be sure to use the side handle (auxiliary
handle) for safe operations.
1. Install the side handle (auxiliary handle) (see
fig. G)
Firstly, rotate the handle counterclockwise relative to the
outer jaw
① to separate the jaws ② , then hold the outer
jaw ① , stick the jaws ② in the grooves ③ on the left and
right sides of the reducer, hold the outer jaw ① with one
hand, and rotate the handle clockwise relative to the outer
jaw
① to tighten it until the jaws ① ② are fixed with the
grooves ③ tightly.
2. Remove the side handle (auxiliary handle)
(see fig. H)
Place the tool on the workbench, hold the outer jaw ①
with one hand, rotate the handle counterclockwise rela-
tive to the outer jaw
① until the jaws ② are loose, and
then remove them from the reducer grooves ③ .
ANTI-SPRAIN FUNCTION
The power tool will shut down quickly, when drill body
suddenly rotates around the bit due to blockage dur-
ing drilling. When the quick shutdown function is in
effect, the LED light will first flash twice slowly and then
flash every 1.5s circularly. Once the On/Off Switch is
released, the LED light stops flashing.
Press the On/Off Switch again to restart the tool.
PROBLEM SOLUTION
1. WHY DOES THE DRILL NOT TURN ON WHEN
YOU PRESS THE SWITCH?
The Forward and Reverse Switch, which is on top of
the trigger, is positioned in the lock function. Unlock the
Forward and Reverse Switch putting it into the required
rotation position. Push the trigger and the drill will start
to rotate.
2. THE DRILL STOPS BEFORE THE SCREW IS
COMPLETELY TIGHTENED. WHY?
Verify the torque position of the Torque Adjustment
Ring, you can find the Torque Adjustment Ring between
the Chuck and the drill body. Position 1 is the lowest
torque (screw driving force) and position 20 is the
highest torque (screw driving force). Position is for
drill operation. Position is for hammer drill operation.
Regulate the Torque Adjustment Ring to a higher
position to reach the best result.
3. I CAN NOT FIT THE BATTERY INTO THE
BATTERY CHARGER. WHY?
The battery can be inserted into the charger only in one
direction. Turn the battery around until it can be inserted
into the slot, the red LED Light should turn on when the
battery is charging.
4. REASONS FOR DIFFERENT BATTERY PACK
WORKING TIMES
Charging time problems, as above, and having not used
a Battery Pack for a prolonged time will reduce the
Battery Pack working time. This can be corrected after
several charge and discharge operations by charging &
working with your drill. Heavy working conditions such
as large screws into hard wood will use up the Battery
Pack energy faster than lighter working conditions. Do
not re-charge your Battery Pack below 0
o
C and above
40
o
C as this will affect performance.
MAINTENANCE
Remove the battery pack from the tool before
carrying out any adjustment, servicing or
maintenance.
There are no user serviceable parts in your power
tool. Never use water or chemical cleaners to clean
your power tool. Wipe clean with a dry cloth. Always
store your power tool in a dry place. Keep the motor
ventilation slots clean. Keep all working controls free
of dust.
FOR BATTERY TOOLS
The ambient temperature range for tool and battery use
and storage is 0
o C -45 o C.
The recommended ambient temperature range for the
charging system during charging is 0
o C -40 o C.
ENVIRONMENTAL
PROTECTION
Waste electrical products must not be disposed
of with household waste. Please recycle where
facilities exist. Check with your local authorities or
retailer for recycling advice.
Positec Germany GmbH
Postfach 32 02 16, 50796 Cologne, Germany