Knurled Nylon Lock Nut
Écrou de blocage moleté en nylon
Contratuerca de nailon moleteada
Nylon Bolt
Boulon en nylon
Perno de nailon
*Bolt can feed through either way.
Base
Base
Base
Pivot Pin
Pivot
Pasador giratorio
Hex Nut
Écrou hexagonal
Tuerca hexagonal
Arm
Bras
Brazo
*Mini Trak T-Nut
*Écrou en T Mini Trak
*Tuerca en T Mini Trak
*Mini Trak Bolt
*Boulon Mini Trak
*Perno Mini Trak
Assemble the Material Support Stop
1.
Slide the center tongue of the Support/Stop Arm between the outside extensions
of the Support/Stop Base and align the pivot hole through all three surfaces.
2.
Insert the Pivot Pin through one outside surface of the Support/Stop Base and
either tap into place with a mallet or a hammer and a block of wood to prevent
marring the end of the Pivot Pin. Continue to advance the Pivot Pin until it is
fully seated in the Support/Stop Base and Support/Stop Arm. Push the
1
⁄
4
"
-20
Hex Nut into the side of the Support/Stop Arm hex recess.
3.
Thread the Nylon Stop Bolt from either side through the Support/Stop Arm
into the Hex Nut. Which side will depend on which side of the Kreg Jig
®
that
the Support/Stop will be used.
4.
Thread the Knurled Nylon Lock Nut onto the Nylon Stop Bolt on the side of
the Support/Stop Arm opposite the Hex Nut. It may be necessary to thread
the Knurled Nylon Lock Nut onto the Nylon Stop Bolt prior to threading the
Nylon Stop Bolt into the Hex Nut in some applications.
NK9292 Version 1
- 01/2018
Material
Support Stop
Assembly and Instructions
Assemblage et instructions
Ensamblaje e instrucciones
ITEM# KJSS
Kreg Jig
®
Uses for the Kreg Jig
®
Support Stop
The Material Support/Stop is a dual function feature that both “Supports” large
panels to keep them perpendicular to the base of the jig, and “Stops” workpieces
in a desired position to easily repeat a 2-hole spacing across a rail.
If you intend to use the Support/Stop mainly as a support, we recommend
that you locate it 8-10
"
from the base of the jig to provide proper support across
the full width of a panel. Add multiple Support/Stops to your work surface to gain
more placement versatility (Item# KJSS). Screw holes are provided to screw
mount the Material Support/Stop to the work surface.
The Material Support/Stop is also designed to function as a position stop.
The end of the Nylon Stop Bolt is positioned to rest against the workpiece to
“center” the workpiece across the predetermined 2-hole spacing. By locking the
Nylon Stop Bolt in position several pieces of the same width may be located
and drilled quickly to minimize the time involved in measuring the pocket hole
location for each workpiece. When the stop position is no longer being used the
Material Support/Stop Arm may be pivoted out of the way to drill panels or large
face frame components. We recommend that you locate the Material Support/
Stop approximately
1
⁄
8
"
to
3
⁄
4
"
from the base of the jig for optimum performance
as a Stop.
You may notice that a notch in the bottom of the Support/Stop Base is sized to
span the profile of Kreg Mini Trak (sold separately). A special T-nut and #10-32
Machine Screw are included with the Material Support/Stop hardware pack for
mounting to the Kreg Mini Trak. By adding a length of Kreg Mini Trak (KMS7509)
to either side of the Kreg Jig
®
Benchtop Base an adjustable Support/Stop system
may be created to allow the drilling of several pocket holes across the width of
large panels at repeatable locations. Mini Trak sold separately.
The Material Support/Stop may also be used with the Kreg Jig
®
Portable Base
as a Stop. Mount the Material Support/Stop adjacent to the Portable Base in a
similar fashion as with the Benchtop Base.
Material Support/Stop shown
in “Stop” position.
Fig. 2A
1
"
tall Material Support/Stop shown
in “Support” position.
Fig. 2B
Material Support/Stop helping
to balance a panel.
Fig. 2C
Material Support/Stop positioning
workpiece for proper placement.
Fig. 2D
Material Support/Stop (Fig. 2A-D)
*Note: Mini Trak Bolt & T-Nut provided for use with Kreg Mini Trak, (KMS7509) sold separately.
WARNING:
!
This product can expose you to chemicals including Acrylonitrile and other chemicals,
which are known to the State of California to cause cancer and reproductive harm. For more information go to
www.P65Warnings.ca.gov.
