manualshive.com logo in svg

Kraun 1KVAH, User Manual, Page: 25 / 29

Share
Download
Kraun 1KVAH User Manual Download Page 25

25

Manual

www.kraun.it

appendix 2: the corresponding working status of indications

no

working status

Indication

warning

Remarks

nor

Bat

Bps

fan

1

line mode
normal voltage

none

  

high/low voltage pro-
tection, turn to battery 
mode

once every four 
seconds

2

Battery mode

normal voltage

once every four 
seconds

Battery Voltage abnor-
mal warning

once per second

3

Bypass mode
main ac normal volt-
age in bypass mode

once every two 
minutes

eliminate after starting the UPS

main ac high voltage 
warning in bypass 
mode

once every four 
seconds

main ac low voltage 
warning in bypass 
mode

once every four 
seconds

4

Battery disconnect warning

Bypass mode

once every four 
seconds

affirm if the battery switch is 
closed

Inverting mode

once every four 
seconds

affirm if the battery switch is 
closed

Power up or start

Six times

affirm if the battery is con-
nected well

5

output overload protection
overload warning in 
line mode,

Twice per second

Remove the less important 
loads

overload in line mode, 
protection

long beeps

Remove the less important 
loads

overload warning in 
battery mode

Twice per second

Remove the less important 
loads

overload in battery 
mode, protection

long beeps

Remove the less important 
loads

6

overload warning in 
bypass mode

once every 2 sec-
onds

Remove the less important 
loads

7

fan fault (fan icon flash)

once every 2 sec-
onds

check if the fan is blocked by 
object.

8

fault mode

long beeps

If display fault code and icon 

 

lights, contact for maintenance 
when you can’t deal with it by 
yourself.

 _indicator lights for a long time

 _indicator flashes

 _the status of indicator depends on other conditions

Summary of Contents for 1KVAH






























Reviews:

No comments