background image

 

12 

WP-501 - Technical Specifications 

 

Technical Specifications 

INPUTS: 

1 composite video (1Vpp/75

Ω) on 2

-pin terminal block connectors 

1 unbalanced audio on 3-pin terminal block connectors 
1 VGA (PC) on 11-pin terminal block connectors (including EDID 
pins) 
1 stereo analog audio on 3-pin terminal block connectors 
1 VGA (PC) on a 15-pin HD connector (including EDID pins) 
1 stereo analog audio on a 3 5mm mini connector 
1 condenser/dynamic microphone on a 3.5mm mini connector 

OUTPUTS (on 
Terminal Block 
Connectors): 

1 VIDEO OUT on 2-pin terminal block connectors 
2 Audio OUT unbalanced stereo audio on 3-pin terminal block 
connectors 
1 VGA (PC) OUTPUT on 10-pin terminal block connectors 
2 relays on 3-pin terminal block connectors 

PORTS: 

E hernet, 1 IR out on terminal block connectors, 1 RS-232 on 
terminal block connectors, 1 USB connector  

DEFAULT IP 
ADDRESS 

192.168.1.39 

SUPPORTED BAUD 
RATES FOR RS-232: 

1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 

DEFAULT EDID 
INFORMATION: 

Standard timings supported: 640x480px60Hz (IBM VGA), 
640x480px67Hz (Apple Mac II), 640x480px72Hz (VESA), 
640x480px75Hz (VESA), 800x600px56Hz (VESA), 800x 600px60Hz 
(VESA), 800x600px72Hz (VESA), 800x600px75Hz (VESA), 
1024x768px60Hz (Native/preferred timing (4:3)) (VESA), 
1024x768px70Hz (VESA), 1024x768px75Hz (VESA), 
1280x1024px75Hz (VESA), 1280x1024px60Hz (VESA STD), 
1280x960px60Hz (VESA STD), 1400x1050px60Hz (VESA STD), 
1440x900px60Hz (VESA STD), 1600x1200px60Hz (VESA STD) 

POWER SOURCE: 

12V DC, 210mA 

DIMENSIONS: 

16.2cm x 3.6 cm x 11.4cm (6.4" x 1.42" x 4.5", W, D, H) 

WEIGHT: 

0.25 kg (0.55lbs) approx. 

ACCESSORIES: 

12V DC, 0.5A power supply, screwdriver 

OPTIONS: 

USB cable 3' (0.91m) (Part number C-UA/MUB-3),  
WP-501 Installation cable, Site-CTRL™ Management Tool Software  

Specifications are subject to change without notice at http://www.kramerelectronics.com 

 

 

 

Summary of Contents for WP-501

















Reviews: