background image

 

 

 

KRAMER ELECTRONICS, LTD. 

Features of the 

VS-1604 

Matrix Switcher 

 

Front/Rear panel features of the 

VS-1604

 are shown in Figure 1; the features are described in Table 1. 

 

 

 

 

Figure 1: VS-1604

 

Front/Rear Panel Features 

 

Table 1: VS-1604 Front Panel Features 

No. 

Feature 

Function 

1. 

 

INPUT SELECTOR 

buttons 

Select the desired input to be switched to the output.

 

2. 

 

OUTPUT SELECTOR 

buttons 

Select the desired output that the input signal is switched to. 

3. 

 

VIDEO OUTPUT STATUS 

Displays the selected video input switched to the output above 

4. 

 

AUDIO OUTPUT STATUS 

Displays the selected audio input switched to the output above 

5. 

 

POWER

 Switch 

Illuminated switch: supplies power to the unit. 

6. 

 

ALL 

When pressed followed by an input button, connects that 

audio/video input to all audio/video outputs.  

7. 

 

OFF 

When  pressed  after  pushing  an  output  button,  disconnects  that 

video/audio output from the video/audio input. To disconnect all 

the outputs, press the 

ALL

 button followed by the 

OFF

 button. 

8. 

 

TAKE 

The  machines  can  operate  either  in  "

Take" 

mode  or  in 

Summary of Contents for VS-1604
























Reviews: