background image

Your RC-7LC / RC-7LCE 

 

4.2  Defining the RC-7LCE Front Panel 

Figure 2 and Table 2 define the 

RC-7LCE 

front panel: 

 

Figure 2: RC-7LCE Front Panel 

Table 2: RC-7LCE Front Panel 

Feature 

Function 

Mounting holes (4) 

For fastening the controller in place  

Configurable Control Buttons (2)  Macro Buttons for controlling the room and the A/V equipment 

Faceplate Attachment Holes (2)  For attaching the faceplate to the controller

1

 

VOLUME Control Knob 

Rotate

2

 to remotely adjust the volume on the power amplifier 

CONFIG

 Port

3

 

Used for Windows®-based configuration software (driver 

downloads, firmware updates and so on)  

IR IN Receiver 

Accepts IR remote commands (for the IR-learner feature)

4

 

SIGNAL SOURCES Buttons 

Select the input source (from 1 to 3) 

 

 

 

 

 

 

 

 
                                                        

1 These screws should not be removed during or after mounting 
2 In a clockwise direction to increase the volume; in a counter-clockwise direction to decrease the volume 
3 Via the front panel, without having to remove the RC-7LCE from its mounting 
4 Letting you configure the RC-7LCE directly from the remote transmitter without the need for software 

Summary of Contents for RC-7LC



















Reviews: