manualshive.com logo in svg

KRAL CGF, Operating Instructions Manual

Share
Download
KRAL CGF Operating Instructions Manual Download Page 55

15 Accessories

15.2 Overflow valve

It therefore has to be ensured through a safety valve at the system that the maximum operating pres-
sure always lies under the opening pressure of the overflow valve.

The overflow valve is offered as a circulation valve (figure left) or as a non-return valve (figure right).

Notice

o

A function test of the overflow valve at least every 5 years is essential for the safe operation 

Ä

 Dur-

ing operation, Page 26.

o

Scope and if necessary shorter test intervals must be specified by the operator-owner in accord-
ance with the requirements and national provisions (for example Austrian Ordinance of Safety and
Health (BetrSichV)).

o

The first function test must take place directly after the commissioning.

o

After longer downtimes (> 4 weeks) the function of the overflow valve must be tested again.

15.2.1

Adjusting the overflow valve

Personnel qualification:

o

Fitter

Aids:

o

Hexagon key

Notice

The opening pressure of the overflow valve is set to 110% of the differential pressure in the factory.

2

2

1

2

1

1

Fig. 16: Overflow valve

1

Screw plug/cap

2

Adjusting screw

 WARNING

Risk of injury through emitted pumped liquid.

Pumped liquids can be hot, poisonous, combustible and caustic.

► Wear personal protective clothing during all the work. Ensure face protection.

► Collect any discharging pumped liquid safely and dispose of it in an environmentally compatible

manner in accordance with the applicable local regulations.

Requirement:

ü

Pressure-side pressure gauge installed

1.

 Switch on the pump and remove the screw plug/cap 

1

 of the overflow valve.

2.

 Increase the supply pressure step-by-step to check the opening pressure of the overflow valve.

Keep an eye on the pressure gauge and make sure that the operating limits are observed.

ð

The opening pressure is reached, when the displayed pressure falls.

3.

 Turn the adjusting screw 

2

 to set the opening pressure:

Turning clockwise: Increase the opening pressure
Turning counter-clockwise: Reduce the opening pressure

4.

 Repeat Steps 2 and 3 until the desired opening pressure is reached.

5.

 Tighten the screw plug/cap 

1

 again.

Operating instructions

OIC 18en-GB Edition 2020-01

55

Summary of Contents for CGF

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands