manualshive.com logo in svg

KRAL CGF, Operating Instructions Manual

Share
Download
KRAL CGF Operating Instructions Manual Download Page 24

10 Operation

10.2 Commissioning

1.

 Open the screw plug of the vent hole 

1

 by a max. of 2 rotations so that air can escape during the

filling process.

2.

 Open the suction-side or pressure-side shut-off device and fill the pump via the suction connec-

tion or pressure connection until pumped liquid is emitted at the vent hole 

1

.

3.

 During the filling process turn the pump shaft or the fan impeller of the motor by hand to speed up

the filling process: 
Filling via suction connection: Turn the fan pump shaft in the direction of rotation of the motor. 
Filling via pressure connection: Turn the pump shaft against the direction of rotation of the motor.

4.

 Retighten the screw plug of the vent hole 

1

.

Filling and venting the pump via the vent hole

Personnel qualification:

o

Fitter

Personal protective equipment:

o

Work clothing

o

Face protection

o

Protective gloves

o

Safety boots

 WARNING

Risk of injury through emitted pumped liquid.

Pumped liquids can be hot, poisonous, combustible and caustic.

► Wear personal protective clothing during all the work. Ensure face protection.

► Collect any discharging pumped liquid safely and dispose of it in an environmentally compatible

manner in accordance with the applicable local regulations.

Requirement:

ü

Shut-off devices in the suction line and pressure line closed

1.

 Open the screw plug of the vent hole 

1

 by a max. of 2 rotations so that air can escape during the

filling process.

2.

 Remove the screw plug of the pressure-side vent hole 

3

.

3.

 Fill the pump via the pressure-side vent hole 

3

, until the pumped liquid is emitted at the vent

hole 

1

.

4.

 During the filling process turn the pump shaft or fan impeller of the motor by hand to speed up the

filling process: 
Filling of the suction chamber: Turn the pump shaft against the direction of rotation of the motor. 
Filling of the sealing chamber: Turn the pump shaft in the direction of rotation of the motor. To
speed up filling of the sealing chamber, fill the sealing chamber of the pump via the vent hole 

1

,

until pumped liquid is emitted.

5.

 Retighten the screw plug of the pressure-side vent hole 

3

.

6.

 Retighten the screw plug of the vent hole 

1

.

10.2.3

Checking the direction of rotation

The direction of rotation is indicated by an arrow on the pump flange. The direction of rotation of the
motor specifies the direction of rotation of the pump. The fan impeller of the motor must rotate in the
same direction in which the arrow for the direction of rotation on the pump flange points.

Notice

Standard direction of rotation: clockwise (viewed from the motor)

Personnel qualification:

o

Fitter

ATTENTION

Dry running can damage pump equipment.

► Ensure that the pump is filled properly.

► Switch the pump on for a maximum of one second and then off again immediately.

1.

 Switch on the power supply and then turn it off again immediately.

24

OIC 18en-GB Edition 2020-01

Operating instructions

Summary of Contents for CGF

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands