background image

MAINTENANCE

 WARNING 

A repair or replacement of this tool must be performed by a quali-

fi ed service technician. For information call our toll free number at 1-866-513-6723.

 WARNING 

Always use only a soft, dry cloth to clean your sander, never use 

any detergent or alcohol.

Disconnect the plug from the power source before cleaning.

 CAUTION 

No chemical agents are approved for use in cleaning this power tool. 

Clean with a dry cloth or towel only.

ACCESSORIES

Sandpaper …………………………………………………………………….....6pcs

Dust Bag ……………………………………………………………………….....1pc

Sandpaper Punch ………………………………………………………………....1pc

 WARNING 

Some dust created by power sanding, sawing, grinding, drilling, and 

other construction activities contains chemicals known (to the State of California) 
to cause cancer, birth defects or other reproductive harm. Some examples of these 
chemicals are:

-Lead from lead-based paints

-Crystaline silica from bricks and cement and other masonry products

-Arsenic and chromium from chemically treated lumber

Your risk from these exposures varies, depending on how often you do this type of 
work. To reduce your exposure to these chemicals: work in a well ventilated area, 
and work with approved safety equipment, such as those dust masks that are spe-
cially designed to filter out microscopic particles.

KRAFTtech

 PS160CA-3 

Page 10

Summary of Contents for PS160CA-3













Reviews: